. .
Page 11 of 25 FirstFirst ... 91011121321 ... LastLast
  1. #101
    OK I will leave it well alone

    Luke is really playing on his wrist

  2. #102
    Quote Originally Posted by luke11cnc View Post
    Luke is really playing on his wrist
    Kids who'd have em eh. . Lol

    I'll try and dig the Xray out of my lads smashed wrist with pins, screws and titanium rods so you can use it as ammunition to show him it could be worse. . . Maybe also put him off expensive motoX as well if your lucky. . lol (Didn't work for my lad thou.!!)

  3. #103
    Cool Jazz

    do you want to see a x-ray of a pace maker??

    James

  4. #104
    Quote Originally Posted by luke11cnc View Post
    do you want to see a x-ray of a pace maker??
    James
    No thanks and on that note don't be playing with those capacitors.!!

  5. #105
    Quote Originally Posted by JAZZCNC View Post
    I'll try and dig the Xray out of my lads smashed wrist with pins, screws and titanium rods
    Did you get to keep the titatium? Useful stuff...

    Quote Originally Posted by JAZZCNC View Post
    No thanks and on that note don't be playing with those capacitors.!!
    If I'd known I wouldn't have shown him my wind turbine as there's lots of big magnets in that. Field is pretty enclosed so should be fine. I've since moved the big neodymium magnet I had left stuck to my lathe just in case!

  6. #106
    Quote Originally Posted by Jonathan View Post
    Did you get to keep the titatium? Useful stuff...
    No it's still in there replacing the smashed bit, I've threatened to remove it a few times thou. .Lol

  7. #107
    Thank's people and yes Jonathan I did see the big magnet on the lathe

    I had to go for a recalibration this week as I walk through a security point and then realized it was a big magnet one

    I'm so lucky it doesn't happen to often:surprised:

    I was at the court house(in Leicester) paying a old old speeding fine from March

    I now have 3 points on my licence and i was only going to the f***ing dentist
    James

  8. #108
    Quote Originally Posted by luke11cnc View Post
    I now have 3 points on my licence and i was only going to the f***ing dentist
    Speeding to the dentist, that's a bit keen!

    Quote Originally Posted by luke11cnc View Post
    Jonathan make it with the extra 1 mm as we can always mill it off if needed??
    I will do that.

  9. #109
    Quote Originally Posted by Jonathan View Post
    Speeding to the dentist, that's a bit keen!

    Yes I was really poorly at Christmas (swine flu) and as a result I smashed three teeth as I hit the floor a bit to fast as I past out, But the pace maker kicked in and I came around pretty quick( go job it's working)

    I also ended up in A&E at one point as I went over in the dentist (police and ambulance turned up) I felt such a fool.

    The teeth cost me a small fortune £600.00 lab fee's alone glad I'm covered on denplan

    James

  10. #110
    well I've tried to get all rails and ballscrews on one plane as suggested and recommended by Jonathan but I can't

    Yes yes I screwed up

    my gantry is to short

    so I have gone with this But I am open to suggestion

    Click image for larger version. 

Name:	Untitled-1.jpg 
Views:	293 
Size:	69.1 KB 
ID:	4552

    I am going to use 50x100 mm extrusion as my main support for the rails and bolted to 6" aluminium

    James & Luke

Page 11 of 25 FirstFirst ... 91011121321 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. BUILD LOG: New Build - For Your Amusement - MK-2 build
    By Karl in forum DIY Router Build Logs
    Replies: 12
    Last Post: 08-02-2017, 08:03 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •