Thread: Diy Brushless Spindle
Hybrid View
-
26-10-2011 #1
Yes I looked for a while for 8mm angular contact bearings but only found one supplier, on eBay in america and not cheap. That was for single row, couldn't find any double row that size.
http://www.ebay.co.uk/itm/708A-8mm-S...0#ht_560wt_905
I wouldn't expect normal bearings to last long if you're drilling ... but nobody really cares as they're so cheap.
Also you can get ER16 collet chucks with 8mm shank:
http://cgi.ebay.co.uk/ws/eBayISAPI.d...ht_4690wt_1080
That's slightly worrying - depends how you go about it.
Poor workman blames his tools :whistling:
-
26-10-2011 #2
Well what the hell....decided to buy a couple of these as they will last longer and will be better than the skate bearings. Will get the other bits as and when I sell more velcro on fleabay and get more money in.
Mark / Jonathan are either of you up for making a bearing housing for me?? For a price of course....
-
26-10-2011 #3Well what the hell....decided to buy a couple
Mark / Jonathan are either of you up for making a bearing housing for me?? For a price of course....
it is probably a good idea if you do a drawing so you can thrash out any problems you might have
-
26-10-2011 #4have you worked out a posh (easy) way to keep the lube in and the crap out of these un-sealed bearings ?
im up to my neck at the moment so hopfully jonathan will pick this up... you will need two stepped washers making unless you can find belleville washers that are 22mm (just under 22mm so they clear the inner housing)
it is probably a good idea if you do a drawing so you can thrash out any problems you might have
-
27-10-2011 #5
-
26-10-2011 #6
I'm only cutting balsa and ply to start with so they will do, but then for the little extra it would cost might be worth getting a larger motor and 10mm spindle?
Also you can get ER16 collet chucks with 8mm shank:
http://cgi.ebay.co.uk/ws/eBayISAPI.d...ht_4690wt_1080
That's slightly worrying - depends how you go about it.
Poor workman blames his tools :whistling:Last edited by njhussey; 26-10-2011 at 06:07 PM.
-
26-10-2011 #7
I maintain there's a tidy little sideliness/embryonic business for someone with the nous to start supplying these brushless spindles in decent numbers to the hobbyist CNC market.
At the minute a CNC hobbyist is faced with Dremel (eeugh) proxxon (nicer but feeble) ...then a leap up to something like kress (good but probably a bit too loud for most...and the price is starting to get chunky).
I reckon if you could knock these out somewhere in between the Proxxon price level (about £90) & Kress level (£150?) ...there'd be good steady demand.
-
26-10-2011 #8
I'd happily make lots of them, but I've not got time now with being at University.
I will probably make some in the holidays. The issue is which motor to choose as it's always a compromise between collet size and max rpm. The ideal way to do it is get a motor which will take an ER20 chuck and rewind it to get the required, higher, rpm (well, kv strictly).
-
26-10-2011 #9
i bought a pair of those 708A bearings but never got around to implimenting them as i ended up using the larger spindles most of the time and the skate bearings seem to be holding up to the amount of use that they get
the 8mm shaft motors make sense if your cutting balsa because of the higher KV choices
I maintain there's a tidy little sideliness/embryonic business for someone
From a quick search on tinternet it seems that most double row angular contact bearings seem to start at 10mm ID
-
26-10-2011 #10
Just bought 2 off 2" dia x 50mm bits of Ali.....one to mess about with and the other to do the propper job :whistling:
I was going to get them and then spend the time whilst they wing their way from the US looking at ways to do it :-)
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Denford router - Brushed router too brushless spindle - Help and advice please
By Tom B in forum Brushless Spindles & MotorsReplies: 4Last Post: 16-05-2016, 09:13 AM -
All-In-One Brushless Servo System
By Gytis in forum Stepper & Servo MotorsReplies: 0Last Post: 22-12-2015, 10:21 PM -
DIY Brushless spindle
By booski in forum Brushless Spindles & MotorsReplies: 2Last Post: 30-10-2013, 09:36 AM -
Using RC Brushless motors as spindle
By Jonathan in forum Brushless Spindles & MotorsReplies: 30Last Post: 20-12-2012, 08:51 PM -
Mach 3 control of DC Brushless motor?
By templecorran in forum Artsoft Mach (3 & 4)Replies: 15Last Post: 18-11-2010, 04:20 PM
Bookmarks