1. I`ve been wanting a little CNC machine for the last couple of years, not specifically for anything, just to learn more about it really. All the work I currently do on my projects (www.raynerd.co.uk) are on my manual machines.

    Despite the constant advice to just go for it and but the bits starting from acratch, I just don`t dare and any machine more complete than this is to expensive, as is buying a bench mill and converting. So this is a cnc build based on confidence and available funds.
    I started with a TEP cnc mill which I paid very little for. These are a sturdy machine and quite well made...just a dreadful design and dreadful software which is locked onto the driver hardware!!
    I was lucky enough to get hold of the original TEP software from a local chap that has converted one of these (isn`t available from anywhere!!) and it was dreadful. Imagine MSWindows Paint, no numberical input (so no saying I want a 20mm line, 10mm from the origin!!, just simple drag and click stuff!!) Then from that, tell the machine to move.

    Here is the machine in its original state:

    Very very bizzare design and many machine limitations:
    • In my opinion the x axis should be mounted so the slides are vertical parallel, not horizontal.
    • No z axis, it is just a solanoid motor to raise and lower the spindle to a fixed level.
    • All hardware is locked so commands can only be sent from the PC interfaced by the TEP software - it won`t talk to Mach or EMC
    • Stepper motors are only about 50Ncm
    • Both axis are fixed off centre to allow space at the back for the electronics
    • Only 12v 5A supply.
    • I had a working CNC machine as a basis/start.
    • If all else failed, I strip it down and the ally plate on it is worth more than the price I`d payed for the machine ! :D
    In truth, there is little going for this other than having a solid working basis to start from....

  2. First job was to strip the electronics completely from it. I will be using a TB6560 3 axis driver. I`ve heard nothing but BAD things about these, but I have one anyway and it`ll certainly get me going if I can avoid blowing it up.
    I wanted to flip the X axis and although replacing the entire side piece would have been ideal, I couldn`t afford it and had some pieces suitable in stock. I raised the sides and used a plate to join them. It may need some supports bridging the sides later on.
    After flipping the X, I could then mount a Z axis. I made the Z axis from a small leadscrew someone kindly gave me and the slides are olite 8mm ID bushes on 8mm silver steel rod slides. The rest is just plate bolted together. There is a problem in that I`ve used a flexible coupling but I haven`t "trapped" the leadscrew. This means that the Z axis compresses on the flexible coupling and moves the relative position of the axis - not good!! This is easy to correct but I haven`t done it yet.
    Once i had the X flipped and raised and the Z built, I couldn`t help try it out... it is running of only 12v at the time and the noise from these small motors is horrific, I think the TB6560 is also to blame but since then I`ve jumped upto 24v and the noise is quieter.

    At this point, the mill went back to its owner while we negotiated price. Other than electronics that we both agreed wouldn`t be needed, it was all replaced to original, thankfully, if he had seen the work I`d put into it I expect the price would have gone up!
    Further updates to come: Now running on 24v from two ATX supplies in series, spindle connected, first door sign engraving done...all good fun! Issues: still not sorted the z axis flexible coupling issue. Is the Z axis height too big. Flex is the spindle.

  3. The spindle is taken from Blackburn Marks advice on a brushless DC motor. Using a ER16 chuck with a 8mm shaft and direct replacement adding a bearing house:

    camera phone shot.

    Up and running, intial tests:

  4. During the last week I`ve stripped the machine to do some mods and in the last few days got it back together. However, I just can`t get my head around the fact that the movement is well out of sync! Just a simple example, say I draw two ovals concentric to one another, they will end up overlapping and even with little flats on them instead of nice curves!

    The wierd thing is, I get the same results on both Mach3 and EMC2... so either I`ve got a setting wrong in the software on both or something is wrong with the TB6560 driver?

    I`m sure it was working OK just last week and so after nearly a full day trying to correct it today, any thoughts or suggestions would be helpful...I`m totally out of ideas!


  5. #5

    Check your wire connections to make sure they are all secure, re-insert all the connections to make sure?
    If the nagging gets really bad......Get a bigger shed:naughty:

  6. #6
    Funny, I just happen to have one of these in front of me and I just happen to come across this thread without searching for it. I cant decide ether to get it working or scrap it for parts, it seems bit of a money pit. Nonetheless I look forward to your progress with this machine.

    P.S TB6560; I heard nothing but bad things about these drivers, after wasting money on them I have brought 3 Pololu a4988 with a Arduino CNC shield to use with my TEP unit.

  7. It's from UK?

Similar Threads

  1. CONVERSION: Clarke milling machine CNC conversion CMD1225D
    By Jonathan in forum Conversion Build Logs
    Replies: 9
    Last Post: 07-05-2017, 02:42 PM
  2. Milling machine CNC conversion - keep hand wheels for manual operation?
    By birchy in forum Milling Machines, Builds & Conversions
    Replies: 5
    Last Post: 23-10-2016, 07:29 PM
  3. NEW MEMBER: Hi Help to build a CNC router/milling machine
    By peterashuk in forum New Member Introductions
    Replies: 1
    Last Post: 27-08-2010, 11:22 PM
  4. Axminster RF31 Milling Machine CNC conversion
    By 1113562 in forum Milling Machines, Builds & Conversions
    Replies: 0
    Last Post: 29-03-2010, 11:42 PM
  5. Chester tools champion 16v milling machine conversion
    By NICKMODELMAKER in forum General Discussion
    Replies: 3
    Last Post: 26-02-2010, 08:29 AM


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts