Page 2 of 3 FirstFirst 123 LastLast
  1. #11
    Quote Originally Posted by 2e0poz View Post
    Priceless!
    What's tickled your Tit's.?

  2. #12
    Tiz shit agreed.. next time I will know though lol ! And i'd like a bit of tit tickling plz !

    It’s like that scene with the cancer patient in Flight film.. “Do I think god gave me cancer? No, do you think he would have given it me if I‘d have asked him to? No. Now I have it do you think he will take it away? No. Course I believe in God.. !!
    Last edited by Fivetide; 21-02-2013 at 01:16 AM.

    Fiction is far more plausible when wrapped around a thread of truth

    Nothing great was ever achieved without enthusiasm.
    Ralph Waldo Emerson

  3. #13
    As for a tool height setting probe, you could always make one like mine - http://www.mycncuk.com/forums/tool-t...-solution.html

    (Yes, I am still alive..!)

  4. #14
    Sorry Jazz i was reading the thread all serious how you was helping out then it was like someone popped your balloon. Can i buy you a new one to say sorry????

    I will admit i am feeling guilty but it was funny......... I went into factors a couple of months ago to get some bits for my car. I asked for some parts for a nissan praire. The guy disappears for about ten minutes and returns with a shed load of bits. He says to me " i knew i had a bunch of stuff hanging around, you can have this lot for nothing as i will never sell it". I had to disappoint him and say i drive a nissan largo. He looked all puzzled to which i replied that if i had said they were for a largo he would not have known what the hell i was talking about. He was quite pissed that he wasted all that time digging the stuff out. I id get the bits i needed though.
    If the nagging gets really bad......Get a bigger shed:naughty:

  5. #15
    Quote Originally Posted by 2e0poz View Post
    Sorry Jazz i was reading the thread all serious how you was helping out then it was like someone popped your balloon. Can i buy you a new one to say sorry???
    No worries.!! It took 10mins from my day so no big deal and like I say sure others will benefit.
    Must admit I didn't think to ask, mainly because thought I'd seen in another thread Fivetide used Mach.? Obviously mistaken Identity.!!

  6. #16
    Quote Originally Posted by JAZZCNC View Post
    No worries.!! It took 10mins from my day so no big deal and like I say sure others will benefit.
    Must admit I didn't think to ask, mainly because thought I'd seen in another thread Fivetide used Mach.? Obviously mistaken Identity.!!
    I bought the board to convert it to Mach 3 then looked at the wireing diagram and though bolloxs to that this works so i'll use it .. and I still like tits strange really as my ex wife didnt have any.. go figure
    Last edited by Fivetide; 22-02-2013 at 12:49 AM.

    Fiction is far more plausible when wrapped around a thread of truth

    Nothing great was ever achieved without enthusiasm.
    Ralph Waldo Emerson

  7. #17
    Quote Originally Posted by Fivetide View Post
    I still like tits strange really as my ex wife didnt have any.. go figure
    No Tit's is good enough grounds for divorce in my Book.!! . . . Having a Mach BOB and not using it is criminal thou.!!!

    Get it swapped over man there's only 15 wires can't be that hard to figure out.! . . . . Will be worth the trouble just to use the probes. You'll also get better cut quality from what I've seen look here. Mach3 vs NC-studio

  8. #18
    Quote Originally Posted by JAZZCNC View Post
    No Tit's is good enough grounds for divorce in my Book.!! . . . Having a Mach BOB and not using it is criminal thou.!!!

    Get it swapped over man there's only 15 wires can't be that hard to figure out.! . . . . Will be worth the trouble just to use the probes. You'll also get better cut quality from what I've seen look here. Mach3 vs NC-studio
    We are lol .. but now shes put on some wood and according to my Dad has a decent set of paps now ! NCstudio is shite ! but I need to live with at for the time being.. cash flow etc. Is sold the BOB coz I need the cash but one day I want 3 -4 machines running of the same board.. dream on lol
    Oh and the good news with the new cutter I have halfed the cut time, and I also see ways of bringing that down by another 50% so from 12 hours to 2.. which is a bonus. Though my maths is shit its still 2hours
    Last edited by Fivetide; 22-02-2013 at 01:45 AM.

    Fiction is far more plausible when wrapped around a thread of truth

    Nothing great was ever achieved without enthusiasm.
    Ralph Waldo Emerson

  9. #19
    Well just in case people want the same for Linux cnc try this, works for me.

    For Science LinuxCnc
    If the nagging gets really bad......Get a bigger shed:naughty:

  10. The Following User Says Thank You to Swarfing For This Useful Post:


  11. #20
    Im having the same problem only Im cutting 25mm mdf. 110mm alphabet A to Z. Im using a 6mm spiral Leitz tool. Spindle speed set at 5000rpm and feed at 7000 although I have this slowed down to 40% as strain on tooling . Im cutting this in 2 steps but its taking over 2 hrs to cut 144 letters..boss thinks Im swinging the lead. If I speed the rpm and feed up it breaks the tool. Are my speeds correct?

Page 2 of 3 FirstFirst 123 LastLast

Similar Threads

  1. Improve Kress TIR or get an upgrade?
    By Hauk in forum Kress Milling Motors
    Replies: 3
    Last Post: 23-02-2014, 06:18 PM
  2. Feeds and speeds
    By dudz in forum Tool & Tooling Technology
    Replies: 0
    Last Post: 26-08-2013, 11:42 AM
  3. trying to improve my board game
    By cubikoman in forum General Discussion
    Replies: 28
    Last Post: 12-05-2012, 06:57 AM
  4. NEW MEMBER: cubikoman needs to improve quality of his boardgame
    By cubikoman in forum New Member Introductions
    Replies: 2
    Last Post: 16-02-2011, 12:17 PM
  5. Dremel into spindal board
    By D-man in forum General Electronics
    Replies: 0
    Last Post: 08-10-2009, 08:42 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •