. .
Page 2 of 3 FirstFirst 123 LastLast
  1. #11
    Lee,

    I don't suppose you can do 12mm x 3mm RH trapezoidal thread Delrin nuts, can you? I've had two goes now at making a tap from bits of lead screw, but both have been too soft to cut the bits of molybdenum filled Nylon I have - they end up twisting.

    I also need a couple of 300mm lengths of 20mm round rail, four carriages and four support brackets, as I've decided to change the design of my Z axis.

    Jeremy

  2. #12
    Sending you a PM now mate :)
    .Me

  3. #13
    Thanks Lee.

    Jeremy

  4. #14
    Quote Originally Posted by progomez View Post
    It looks the same. What about I buy 1 8mmx8mm now and if it doesnt fit ill buy a 6,35x6,35 to make a pair.

    Hold on the delrin nuts for now although I may build a cnc to sell and will need them for that.

    Email an invoice and ill pay with paypal.
    Whats your paypal address mate? email it to me.
    .Me

  5. #15
    Thanks for the parts, Lee. All arrived OK and look to be just the job!

    Jeremy

  6. #16
    Quote Originally Posted by Jeremy View Post
    Thanks for the parts, Lee. All arrived OK and look to be just the job!

    Jeremy
    Hi sorry i ment to email you regarding that order, glad you recived them ok. Dont forget to run your new design past me, nothing like seeing your own kit put to use ;)
    .Me

  7. #17
    Just to be clarify ....these delrin drive nuts, would allow me to connect my M8 threaded rod (lead screw), to my stepper motor shaft (which I think is 6.35mm - from recollection).

    Would these need any modd'ing or are they ready to rock?

    If so, could you please quote me for 3 of them (inc delivery - UK based )

  8. #18
    No they are used as nuts that run up and down your threaded rod, as the motor turns the threaded rod your axis table moves :).

    .Me

  9. #19
    Now I'm confused.

    the post is entitled Delrin Drive nut (& it was always my interpretation that a drive nut is like the pic you've just posted above!), but in post 5 on this same thread (ie back on page ), has this photo...



    in that photo they look like couplers? (so the thread morphed a little & confused me!)

    (original post - [ame="http://www.mycncuk.com/forums/showpost.php?p=2745&postcount=5"]MYCNCUK - View Single Post - Delrin drive nut (lee)[/ame] )

    Do you still sell the pictured couplers as mentioned in the photo in 'post 5' of this thread for £7 each? (specifically M8 threaded rod to stepper shaft of 6.35mm diameter)

    I reckon there's a good business op for someone to knock these couplers out at a reasonable 'pack of three' cost! (as all the couplers I've seen to date would mean if I bought them, it would result in more cost than the rest of my whole CNC build!)
    Last edited by HankMcSpank; 04-04-2009 at 09:36 PM.

  10. #20
    The thread is about drive nuts, but in post 5 he says "I also have some of these" above the couplers photo.

Page 2 of 3 FirstFirst 123 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Delrin Lead nuts.
    By Kammo1 in forum Gantry/Router Machines & Building
    Replies: 14
    Last Post: 27-01-2016, 08:36 PM
  2. coloured delrin/acetal uk suppliers?
    By dazza in forum Marketplace Discussion
    Replies: 5
    Last Post: 26-05-2014, 12:35 PM
  3. Tapping Delrin for M10 threaded rod - doable?
    By HankMcSpank in forum Machine Discussion
    Replies: 7
    Last Post: 02-02-2013, 12:31 AM
  4. Delrin & Nylon S & F please
    By craigrobbo in forum Machine Discussion
    Replies: 2
    Last Post: 21-07-2012, 12:19 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •