. .
  1. #1
    Hi, I've been making my brain hurt looking at stepper motors, torque ratings,
    etc. but I've noticed something a bit odd.

    It appears that to get the best performance from a stepper it should be driven at ~20 times its rated voltage, or 32 times the square root of the coils inductance in mH (this makes more sense considering the step input voltage / current curve of an inductor).

    Looking at several motors in the 1.8 to 3Nm range this would equate to a driving voltage of around 60 to 100V, but most (cheap) drivers seem to have output voltage limits of around 35 - 48V, which would imply not getting the best from the motors.

    Anyone know of any drivers with higher voltage capability available in the UK that don't cost an arm and a leg?

    I know drivers are available like the MCP MSD980 - 7.8A @ 90V, but £105+VAT per axis is too steep for me at the moment. :(

    I look forward to any information you can share.

  2. #2
    Thanks for that, I've been trawling EBay looking for bargains, but I hadn't thought to try the non-UK versions of the site.

    Following the link you gave I found a much more reasonable 3 axis driver kit that does 60V @ 5A, but nothing higher.

    Time to hit the books again to try and find out how much lower voltages hurt performance :(.

  3. #3
    5A is fine for most sensible steppers up to around 12Nm, it's the voltage I want higher, to play it safe with voltage spikes on the mains supply I'd have to drop to 10+% below the max voltage, or invest in a regulated supply. And that would drive the cost up again :(.

    I thought on imports the tax was just paying the VAT? (Unless I get it sent marked as a gift :D).

  4. Voltage makes a differnece to top speed performance, but do you need it?
    You mention 1.8-3 Nm, so you are within the Nema 23 range, so look for a motor that is as high current as possible, to keep the inductance as low as possible.
    There are disadvantages to high voltage as well; the motor will get a lot hotter, and will make a lot more noise.
    In my experience for a nema 23 motor 40-50 V is fine, and going up to 70 V will only give you a performance increase at the higher speeds. (Over 300 RPM)
    Do you want to pay 50-60% more for 15-20% more performance?
    What torque and speed do you need?
    Nema 34 motors are different, and these really need high voltage to get the best from them.

  5. #5
    Thanks Gary, food for thought there. I agree higher current, lower inductance motors have lower voltage requirements as well.

    Slightly confused as to higher voltages causing more noise :confused: why would this be?

    -
    The more I learn about this hobby, the brighter the light of knowledge grows, the deeper is the pit of ignorance revealed...

  6. I am not sure why it makes more noise, will have a look into it and post later.

    Quote Originally Posted by ZeroCount View Post
    Thanks Gary, food for thought there. I agree higher current, lower inductance motors have lower voltage requirements as well.

    Slightly confused as to higher voltages causing more noise :confused: why would this be?

    -
    The more I learn about this hobby, the brighter the light of knowledge grows, the deeper is the pit of ignorance revealed...

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. What voltage for stepper drive?
    By Davek0974 in forum Plasma Table Machines
    Replies: 1
    Last Post: 22-01-2014, 10:49 PM
  2. Optimum voltage for M60STH88-3008DF steppers and 752 drivers?
    By Mad Professor in forum Stepper & Servo Motors
    Replies: 6
    Last Post: 26-08-2012, 09:38 PM
  3. FOR SALE: Stepper Drivers + PSU's
    By Shinobiwan in forum Items For Sale
    Replies: 8
    Last Post: 16-03-2012, 11:05 PM
  4. FOR SALE: 3 x 2.5Amp 30V Stepper Drivers
    By michael in forum Items For Sale
    Replies: 11
    Last Post: 13-08-2011, 02:10 PM
  5. 2M2280N High Voltage Stepper Driver
    By Robin Hewitt in forum Motor Drivers & Controllers
    Replies: 19
    Last Post: 14-11-2009, 08:43 AM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •