1. #1
    I just bought an enclosure, cnc / liquid gasket printer, for the desktop Isel Techno FB2 that was inside.
    so I am offering all the bits that I don't require, but I do want new motors and controllers, mach3/4 and that, anyways here goes

    here is what I bought, took two goes in my little estate car, Fulham London to Stafford, but at least now it is all in bits


    the long side are 90 by 45 = 1450mm
    there are six bits
    -----------------------
    the short sides are 1080mm
    there are 6 bits of this - maybe 8
    --------------------------
    the legs are 90mm by 90mm and have bolt in feet
    ------------------------------------
    there are 4 complete blue panels, for all 4 sides
    the buttons on the front could be for auto stop
    -----------------------------------------

    if you left it as it is, max width is 1080 plu 90 plus 90 = 1260mm, 4ftand a smidgers
    the long then is 1450 plus 90 - leaving the tall legs = 1540mm, 1525 is 5ft

    -------------------------------------------
    theer are 2 bits of 90 by 45 to make the y axis with, i think another few lengths to make a shelf on the tall legs, and the z axis

    -------------------------------------------

    there are 2 3/4'' 19mm solid alloy plates to make the gantry ends, there are another two bits of 15mm or 19mm to make the z axis

    -------------------------------------------

    there are 4 four foot flat sliders with bosch bearings, enough to then do the y axis and loads to make a very rigid z axis.
    these are fitted to 4 bits of 60 by 45mm -
    THERE ARE ALSO A PAIR OF IAR RAMS AND 2 PUMPS AND LOTS OF PNEUMATIC CONTROLLING STUFF - I DON'T KNOW WHAT IT DOES THOUGH.

    there are two of those alloy thick plates with a nice hole in the centre for you to cut a pair of welly boots from, and have the nice radius


    ----------------------------------------------
    also there is stack and stacks of 45mm box, lots of nuts and bolts

    all the wireing is there to the controllers about 1998 from what I can see, I can take a pic.

    ------------------------------------------------

    there are 2 old wee amc 3 axis controllers, , two hand held doofers, all the wireing and connectors

    two of these
    and two of these, the other one is a bit bigger all full of giblets

    have all the wireing and connectors too.
    ---------------------------------------
    there are two BUSHE pumps, rams, connectors and valves
    -----------------------------------
    location magnet things for 3 axis, 3 on each,
    also have a trend t10 1/2 inch collet 2000kw plunge router, used for about 2 hours - ten years ago, in the case.
    also have a 100a invertor / tig welder plasma cutter
    i really should nail together a 4foot by 2 foot plasma table........

    all used

    IT IS ALL APART, YOU CAN GET IT IN AN ESTATE CAR

    I AM WILLING TO POST EVERYTHING - BAR THE BLUE SIDES AT COST.

    NOW THE BEST BIT i NEED
    Nema23 Stepper Motor Kit 3.1Nm x 3 Axis
    ALSO NEED A SPINDLE AND MOUNT
    AND SOME MACH3 - OR 4
    OH AND A USB/lan BOB

    SO HAPPY TO HAVE A SWAPSIES.
    THANKS
    Last edited by nobby; 10-06-2013 at 10:16 PM.

  2. #2
    Quote Originally Posted by nobby View Post
    I just bought an enclosure, cnc / liquid gasket printer, for the desktop Isel Techno FB2 that was inside.
    so I am offering all the bits that I don't require, but I do want new motors and controllers, mach3/4 and that, anyways here goes

    here is what I bought, took two goes in my little estate car, Fulham London to Stafford, but at least now it is all in bits


    the long side are 90 by 45 = 1450mm
    there are six bits
    -----------------------
    the short sides are 1080mm
    there are 6 bits of this - maybe 8
    --------------------------
    the legs are 90mm by 90mm and have bolt in feet
    ------------------------------------
    there are 4 complete blue panels, for all 4 sides
    the buttons on the front could be for auto stop
    -----------------------------------------

    if you left it as it is, max width is 1080 plu 90 plus 90 = 1260mm, 4ftand a smidgers
    the long then is 1450 plus 90 - leaving the tall legs = 1540mm, 1525 is 5ft

    -------------------------------------------
    theer are 2 bits of 90 by 45 to make the y axis with, i think another few lengths to make a shelf on the tall legs, and the z axis

    -------------------------------------------

    there are 2 3/4'' 19mm solid alloy plates to make the gantry ends, there are another two bits of 15mm or 19mm to make the z axis

    -------------------------------------------

    there are 4 four foot flat sliders with bosch bearings, enough to then do the y axis and loads to make a very rigid z axis.
    these are fitted to 4 bits of 60 by 45mm -
    THERE ARE ALSO A PAIR OF IAR RAMS AND 2 PUMPS AND LOTS OF PNEUMATIC CONTROLLING STUFF - I DON'T KNOW WHAT IT DOES THOUGH.

    there are two of those alloy thick plates with a nice hole in the centre for you to cut a pair of welly boots from, and have the nice radius


    ----------------------------------------------
    also there is stack and stacks of 45mm box, lots of nuts and bolts

    all the wireing is there to the controllers about 1998 from what I can see, I can take a pic.

    ------------------------------------------------

    there are 2 old wee amc 3 axis controllers, , two hand held doofers, all the wireing and connectors

    two of these
    and two of these, the other one is a bit bigger all full of giblets

    have all the wireing and connectors too.
    ---------------------------------------
    there are two BUSHE pumps, rams, connectors and valves
    -----------------------------------
    location magnet things for 3 axis, 3 on each,
    also have a trend t10 1/2 inch collet 2000kw plunge router, used for about 2 hours - ten years ago, in the case.
    also have a 100a invertor / tig welder plasma cutter
    i really should nail together a 4foot by 2 foot plasma table........

    all used

    IT IS ALL APART, YOU CAN GET IT IN AN ESTATE CAR

    I AM WILLING TO POST EVERYTHING - BAR THE BLUE SIDES AT COST.

    NOW THE BEST BIT i NEED
    Nema23 Stepper Motor Kit 3.1Nm x 3 Axis
    ALSO NEED A SPINDLE AND MOUNT
    AND SOME MACH3 - OR 4
    OH AND A USB/lan BOB

    SO HAPPY TO HAVE A SWAPSIES.
    THANKS
    erm, controlling stuff sold

    NOW REQUIRE A SPINDLE AND MOUNT.
    A USB BREAK OUT BOARD

    HAVE NEW MOTORS
    FOR SALE 2 ROUND NEMA 23'S 8 WIRE, AND A 6 WIRE SUARE ONE
    ALSO 3 1/4 -TO - 1/4'' CONNECTORS

    NEED SPINDLE AND MOUNT AND SOFTWARE.

    COME ON!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
    STEVE
    0774 858 2044
    LOADS OF 40MM BOX

    YOU COULD MAKE A HALFF DOXEN TABLE YOPS

  3. #3

    TWO
    metal work cnomo air rams/ type 1133 bore 32mm stroke 600mm
    FOUR

    bosch pop up solenoids
    TWO


    bushe pumps, I think the otehr one is thesame, its in the garage away from the house.
    will exchange for
    ONE - 2.2kw spindle and invertor, with the 80mm mount - ebay

    pics of isel Techno FB2 motors, a PAIR in good order 100


    eight wire
    ----------------
    ONE
    six wire sanyo nema style 23, with 1/4'' out 76mm long
    25


    this macjhine was a twin feed pneumatic track that locked, so as tyo have a mobile phone gasket printed onto it

    the tacks do not come with the pneumatics, but they are for sale
    you could bolt it all back together, It was 'JUST' too heavy for me to manage, plus I had to get it out of the main machine

    -------------------------------

    STOP PRESS
    4' by 5' table 500, comes with metal sides and twin side rails
    Last edited by nobby; 14-06-2013 at 04:03 PM.

  4. #4
    pneumatics sold
    controllers sold
    odd rails sold
    just the 5 by 4 table with sides left.

    oh and a few lengths of 45 by 45
    Last edited by nobby; 27-06-2013 at 05:34 PM.

Similar Threads

  1. Replies: 2
    Last Post: 29-05-2014, 11:33 PM
  2. Effect of Forces on Gantry Cross-Sections?
    By WandrinAndy in forum Gantry/Router Machines & Building
    Replies: 37
    Last Post: 22-12-2012, 10:34 PM
  3. Straight sections of box steel
    By gavztheouch in forum Metalwork Discussion
    Replies: 2
    Last Post: 03-01-2012, 02:37 PM
  4. FOR SALE: Lots of Bosch Rexroth Aluminium extrusion 50mm x 50mm.
    By michael in forum Items For Sale
    Replies: 12
    Last Post: 12-10-2011, 08:52 AM
  5. FOR SALE: Z slides ??
    By John S in forum Items For Sale
    Replies: 4
    Last Post: 27-09-2009, 11:03 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •