. .
Page 1 of 2 12 LastLast
  1. #1
    Tom's Avatar
    Lives in Nottingham, United Kingdom. Last Activity: 11-11-2023 Has been a member for 9-10 years. Has a total post count of 176. Referred 1 members to the community.
    It's time to start thinking about motor power and leadscrew pitches for my machine.

    What's the best way to approach this?
    I've seen people talk about target speeds, target accelerations (0.5g? 1g?), gantry weights, cutting forces, motor curves, etc.

    I should say that I'll be using trapezoidal leadscrew, which will have a much lower efficiency than ballscrews. Before now I've been thinking about 3Nm motors, but perhaps I don't need all that power.

    Practically speaking, having never done this before, where is the best place to start?
    Acceleration seems more important than top speed for the relatively compact routing I'm going to do (many direction changes), but what should I aim at? What do you lot use?

    Speed is much easier - I'd ideally like to achieve a jog speed of 120mm/s (~280 IPM), which is 900rpm on an 8mm pitch leadscrew. Can steppers do that speed? I'm thinking cutting speed will be less closely linked to motor power, more to router power, chip load, and machine rigidity.

    Cutting force seems important too, but what figures should I use? Or should I worry about it less and just bolt some stuff together?

    Kip, Smiler, Lee,
    What do you think? How do you do it? :question:

  2. #2
    Hi, the other more qualified guys will be along to give you the right methods’ of doing the above.

    What I can tip you with however is, motors with a lower inductance communicate faster/better with the driver cards, what this means is you get better speeds from the motor when changing direction and so on.

    The trade off seems to be finding a motor with low inductance that has a high holding torque.
    .Me

  3. #3
    Tom's Avatar
    Lives in Nottingham, United Kingdom. Last Activity: 11-11-2023 Has been a member for 9-10 years. Has a total post count of 176. Referred 1 members to the community.
    Thanks for your help Kip,

    The build's coming along nicely (so more pics soon)...

    I'll fudge the motor power together using 3NM motors I think... At least I'll have some decent parts to move over to machine #2!!

    It really is time to think about leadscrews now. What about leadscrew whip? My X axis screw will be 1600mm long (63"). I was hoping to get away with 16mm (or 18mm) diameter. What do you recon?

  4. #4
    Accelerations are a consideration when you slam it in to reverse.

    I'd say find the top speed where you can reverse without losing steps, halve it, then apply accelerations/decelerations above that point.

    You'll probably find you only need them for the G00's a stepper motor makes a pretty good brake

  5. #5
    Tom's Avatar
    Lives in Nottingham, United Kingdom. Last Activity: 11-11-2023 Has been a member for 9-10 years. Has a total post count of 176. Referred 1 members to the community.
    Robin, thanks for your info. If I understand your approach it's more aggressive than I imagined would be possible - I was planning to use accel and decel values for all starts and stops (can be set in EMC2, not sure about mach3). Just to check my understanding, you only find it necessary to apply accel and decel above a certain speed, and below this speed you can go from forward to reverse with no ramping?

    I might try for 19mm or 20mm then. But belts, - I haven't designed the machine for those at all... :nope:

    Kip, is this the "patented" design of which you speak? :naughty: Seems quite clever, but can you really patent that?

    I did a search for Mike Everman actually. He seems to be everywhere. One of the threads lead me to this (start of geek voice) very interesting (end of geek voice) looking book. Would probably answer all my questions... :geek:

  6. #6
    Tom's Avatar
    Lives in Nottingham, United Kingdom. Last Activity: 11-11-2023 Has been a member for 9-10 years. Has a total post count of 176. Referred 1 members to the community.
    Would probably answer all my questions...
    Hmm, maybe not. Having had a read online its more about the cutting load than the inertia...

  7. To work out critical speed use this calculator.
    It works very well.
    All you need is the root diameter, length of the screw and how you are supporting it and it will work out the max speed.

    http://www.nookindustries.com/ball/B...#CriticalSpeed



  8. #8
    Tom's Avatar
    Lives in Nottingham, United Kingdom. Last Activity: 11-11-2023 Has been a member for 9-10 years. Has a total post count of 176. Referred 1 members to the community.
    Thanks Gary, that's really useful.

    Just for my future ref:
    RPM Root Dia (mm)
    600 12.7
    700 14.8
    800 16.9
    900 19.1
    1000 21.2

  9. #9
    Problem I see is one of resolution.
    Take the smallest pulley you can use without undue belt wear, say 20 teeth for round figures and you are running on 5mm pitch belting so one rev moves 100 mm.

    Now a standard stepper moves 200 steps per rev so one step will equal 0.5mm or 0.0197" say 20 thou per step.

    Dropping to 10 microsteps which is about the max usable without shedding oodles of torque will reduce this to 0.05mm or 0.00197" or 2 thou per step.

    Without another belt reduction in the system somewhere before the 20 T pulley or using servos with high count encoders [ which will also reduce speed ] this system has limitations, patent or not.

    .
    John S -

  10. You mentioned using leadscrews, is this for price?
    A leadscrew is not that efficient and you should expect between 40-60% for a lead screw and up to 90% for a ball screw.
    This means that with a leadscrew you will need up to 50% more power to get the same amount of force.
    So, because of this you may be saving on the leadscrew but will need to spend more on the motor and driver.

    Gary


    Quote Originally Posted by Tom View Post
    It's time to start thinking about motor power and leadscrew pitches for my machine.

    What's the best way to approach this?
    I've seen people talk about target speeds, target accelerations (0.5g? 1g?), gantry weights, cutting forces, motor curves, etc.

    I should say that I'll be using trapezoidal leadscrew, which will have a much lower efficiency than ballscrews. Before now I've been thinking about 3Nm motors, but perhaps I don't need all that power.

    Practically speaking, having never done this before, where is the best place to start?
    Acceleration seems more important than top speed for the relatively compact routing I'm going to do (many direction changes), but what should I aim at? What do you lot use?

    Speed is much easier - I'd ideally like to achieve a jog speed of 120mm/s (~280 IPM), which is 900rpm on an 8mm pitch leadscrew. Can steppers do that speed? I'm thinking cutting speed will be less closely linked to motor power, more to router power, chip load, and machine rigidity.

    Cutting force seems important too, but what figures should I use? Or should I worry about it less and just bolt some stuff together?

    Kip, Smiler, Lee,
    What do you think? How do you do it? :question:

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. ACME / Trapezoidal leadscrews
    By ZeroCount in forum Lead Screws, Nuts & Supports
    Replies: 8
    Last Post: 08-03-2020, 09:29 AM
  2. Belt Driving your leadscrews !
    By Lee Roberts in forum Lead Screws, Nuts & Supports
    Replies: 11
    Last Post: 05-02-2011, 09:14 AM
  3. Restoring old lathes, backlash in leadscrews
    By irving2008 in forum Lathes, Lathe Rebuilding & Conversions
    Replies: 28
    Last Post: 08-09-2009, 12:05 AM
  4. Ideas for fitting leadscrews
    By irving2008 in forum Lead Screws, Nuts & Supports
    Replies: 8
    Last Post: 11-11-2008, 10:05 PM
  5. motors in the UK
    By sensph in forum Stepper & Servo Motors
    Replies: 12
    Last Post: 28-08-2008, 11:30 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •