1. #1
    isel fb1 cnc router used
    1 new 5 axis usb break out board digital dream
    3 new nema 23 sanyo motors
    3 new tb6600 2by3 drivers
    1 new 36 v 10a psu
    1 new 300 by 200 by 100 electronics box
    new iec connector with ferrite rings
    new 1..5mm 7 core wire cut to length, with metal glands in the mootor cans
    ferm 500watt spindle 1/8ths bits

    needs a little wireing in the controller - i.e. drill some holes for the motor cables - and wire up the drives thats all - its all tested and works, the cables have the wires for the limit switches in them - these need connecting in the box



    ooh I bent the limit switch stricker on the y axis - needs replacing

    stock they are 1604 ballscrews
    motors are 56mm 4 wire.

    1200
    steve
    0 seven 74 858 204 four

    its a really old table but with brand new electronics!!!!!!!!!!
    i only want the money to buy servo motors and drives and control for my other machine.


    its like that, but the y axis cover is now gone.
    quality isel anti back-lash nuts
    precision ball screws
    boshe linear bearings
    its a beaut but old.

    still, the elestacsa are all brand new....................
    the r3eason i havn't finished it - its in the shed
    i was going to make it a plasma table but now realise its not feasable
    the motors and elecrtics are indoors though, gives you the optiion of doing it how you likey

    also have about 30 nema 23 56mm motors 15 each
    8 dual shafted nema 17 the big ones 12 each

    will also have soon 8 wire nema 23's 76mm, and another complete controller 3 axis 36v with a leaftboy smooth stepo card all done - will even come with motor cans and mounts. 450 = complete controller with motors 8 wire bi-polar parrallel - when my servo shiz is finished mind

    plus have another usb break out board 54
    -------------------------------------------------

    what i mean is...
    the z axis is off, but has the motor and wireing all done
    7 core 1234 = a+ a- b+ b- 5 and 6 are limit switches, the 7th is an earth that you rivent to the motor can and then back into the electronics box
    all the motors are wired- soldered and heatshrunk, simply need fitting on
    connecting to the drivers 1234
    and the drives to the bob 1234
    and the limit switch wires 12 12 12 to the bob

    you ned to take it all off anywayt o get it in your boot.

    it sis just about 'hernia' a one man lift

    thank you
    Last edited by nobby; 18-11-2014 at 06:53 PM.

  2. #2


    controoller - note I have two of them usb break out boards




    ffffff


    nema 23 inside motor can/sheild - motor mount - two little screws hold limit switch - hidden in can - no emf

    erm connectors are 1/4'' to 1/4''

    z axis can has a 56mm x and y could take 76 or 81mm - you don't need to run the cans

    the connectors pictured are not connectors, merely 'tidy looking' glands that nip up
    7 wire cables 6 core and an earth 1.5mm core numbered 1-6 easy to wire up




    has rocker switch but isn't variable speed.

    you could have it going in half an hour 'with the lid open on the controller and simply plug in the wires..........................
    Last edited by nobby; 19-11-2014 at 03:55 PM.

  3. #3
    Hi
    What model is it, at Isel web at read then fb1 have only 350X290mm but fb2 550X540mm. If there no lifts in to bearings I have interest about it, I'll buy in this week one router. Tonigh I'll get qoute for 6040 Chinese router, but your looks interesting as well. Please let me know about sizes
    #
    Quote Originally Posted by nobby View Post
    isel fb1 cnc router used
    1 new 5 axis usb break out board digital dream
    3 new nema 23 sanyo motors
    3 new tb6600 2by3 drivers
    1 new 36 v 10a psu
    1 new 300 by 200 by 100 electronics box
    new iec connector with ferrite rings
    new 1..5mm 7 core wire cut to length, with metal glands in the mootor cans
    ferm 500watt spindle 1/8ths bits

    needs a little wireing in the controller - i.e. drill some holes for the motor cables - and wire up the drives thats all - its all tested and works, the cables have the wires for the limit switches in them - these need connecting in the box



    ooh I bent the limit switch stricker on the y axis - needs replacing

    stock they are 1604 ballscrews
    motors are 56mm 4 wire.

    1200
    steve
    0 seven 74 858 204 four

    its a really old table but with brand new electronics!!!!!!!!!!
    i only want the money to buy servo motors and drives and control for my other machine.


    its like that, but the y axis cover is now gone.
    quality isel anti back-lash nuts
    precision ball screws
    boshe linear bearings
    its a beaut but old.

    still, the elestacsa are all brand new....................
    the r3eason i havn't finished it - its in the shed
    i was going to make it a plasma table but now realise its not feasable
    the motors and elecrtics are indoors though, gives you the optiion of doing it how you likey

    also have about 30 nema 23 56mm motors 15 each
    8 dual shafted nema 17 the big ones 12 each

    will also have soon 8 wire nema 23's 76mm, and another complete controller 3 axis 36v with a leaftboy smooth stepo card all done - will even come with motor cans and mounts. 450 = complete controller with motors 8 wire bi-polar parrallel - when my servo shiz is finished mind

    plus have another usb break out board 54
    -------------------------------------------------

    what i mean is...
    the z axis is off, but has the motor and wireing all done
    7 core 1234 = a+ a- b+ b- 5 and 6 are limit switches, the 7th is an earth that you rivent to the motor can and then back into the electronics box
    all the motors are wired- soldered and heatshrunk, simply need fitting on
    connecting to the drivers 1234
    and the drives to the bob 1234
    and the limit switch wires 12 12 12 to the bob

    you ned to take it all off anywayt o get it in your boot.

    it sis just about 'hernia' a one man lift

    thank you

  4. #4
    Quote Originally Posted by realking View Post
    Hi
    What model is it, at Isel web at read then fb1 have only 350X290mm but fb2 550X540mm. If there no lifts in to bearings I have interest about it, I'll buy in this week one router. Tonigh I'll get qoute for 6040 Chinese router, but your looks interesting as well. Please let me know about sizes
    #
    hello its all sold
    it all went for 650

Similar Threads

  1. Replies: 0
    Last Post: 27-06-2014, 10:24 PM
  2. SOLD: ISEL Flatcom 20 (700x600mm) with AM882 drivers
    By badgerman in forum Items For Sale
    Replies: 2
    Last Post: 27-06-2014, 10:45 AM
  3. chinese TB6600 drivers
    By jonnydeen in forum Motor Drivers & Controllers
    Replies: 6
    Last Post: 04-06-2013, 09:37 PM
  4. 2x Motors, 2x drivers. How about breakout?
    By Tenson in forum Motor Drivers & Controllers
    Replies: 2
    Last Post: 20-09-2012, 03:21 PM
  5. FOR SALE: Isel-automation Flat bed X-Y table with motors and mounting plate
    By Vespa Mad in forum Items For Sale
    Replies: 8
    Last Post: 27-08-2009, 08:45 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •