-
25-03-2015 #1
Well they both arrived finally and I'm in the stuff now . Will do as best as possible to provide way to many pics and other menial info regarding these 2 Engravers .
If this thread is in the wrong forum , please place it where you feel it should reside . Kind of like me ( reside ) Canadian living in the States .
Tiny rails and bearings ( were the first thing that surprised me from the darn weight of the machine , ( hernia in the making ) electronics boxes are just as bad weight wise compared to what is out there now . Yet considering they are totally discontinued and parts may be SOL . The height of the Y axis from the table is so do able in increasing it , wonder why it wasn't done years ago . ( side plates for the gantry would just need to be made taller ) plus longer stroke on the Z .
Came with one flood hose attachment but the gauge is trashed , all the cables look in real good condition first glance .
Lead screws are as small as the rails almost ( tight pitch ) guess that's why there have been complaints the machine moves so slow .
The spare 20mm rails and bearing blocks I have may not be an easy swap over , but they worked fine for Gerber in the first place .
The tables look okay as well with no obvious gouges taken out of them , T-slot channels are not all chewed up either . So it looks like they will make the grade so far .
Electronics is another thing , but that will come later . If they get to be more headaches than their worth , plus I really don't want to be tied down to their software currently .
Will provide measurements also if anyone has any need if they are curious .
thanks all and all that good stuff
-
25-03-2015 #2
All rails are 12 mm dia and corresponding bearing blocks ( inserts ) ( no makers marks )
12.5 mm dia lead screws / 10 threads per inch ( X, Y, and Z axis )
Superior Electric Slo- Syn Motors Synchronous/Stepping , Type M063-LS-516 , 2.25 volts Dc , 4.6 Amps , Steps/rev 200 Rpm @ 60 Hz ( 6 Pin connection )
Damaged limit switches mounted to bearing blocks ( 4Z12 ) ( no makers marks )
usual dust boot 12mm rails again
Sry for the shaky pics , coffee withdrawlLast edited by Kru82; 26-03-2015 at 12:02 AM.
-
26-03-2015 #3
Last edited by Kru82; 26-03-2015 at 06:27 AM.
-
26-03-2015 #4
Data sheet for those specific motors
-
29-05-2015 #5
have made you made any more progress
i just obtained a d200 witch i am currently striping to clean as my one is in a very dirty state
planning on changing drive electronics to something current
-
02-07-2015 #6
It has been awhile , and sry to anyone looking how I made out with mine .
Did a total swap of all the Gerber electronics and motors , went with gecko G540 ( http://www.cncrouterparts.com/3-axis...-kit-p-74.html ) and mach 3 . On both machines I kept windows xp and only the very basics on the comp . ( stand alone ) no net no virus no other junk that was basically a waste . Turned off all updates and and firewall since it is not connected to the net . They work great and have some issues with file transfers from other comp Cd's and that about it .( could be just old CD's ) Use a memory stick will prob be a better means to end anyway .
Since all the lead screws are identical , settings through mach 3 is just a matter of typing in the same settings
So now I have extra Arc stations and the rest to part with to whom ever needs some items .Last edited by Kru82; 02-07-2015 at 03:16 AM.
-
02-07-2015 #7
This week will finally get around to making new gantry side plates to increase the z height , 2 - 3 inches added , with new spacer blocking under the gantry that bolts to the rail track mounts . Will prob have to re surface the table top but that's no big issue to worry about . Change the plumbing for the vac table to front rather than rear and separate sections plumbed and valved just for specific table areas worked on . scooper1 , if you need the exact settings can pass them along no worries , that is if your going with same set up .
Last edited by Kru82; 02-07-2015 at 03:19 AM.
-
03-07-2015 #8
Have the first set of gantry side plates ( all they had was 5052 no 6061 plate ) done , extra 2 inches in height from the factory for max material thickness that can be done is now 4.25 inches . 2 x 4 x 6 square channel tubing also as the spacer to bolt in .
-
02-09-2015 #9
I am interested in the arc stations and the rest if they are still available.
Extra parts for the D200s we have would be good.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
FOR SALE: Roland engravers
By Bartell in forum Items For SaleReplies: 3Last Post: 11-12-2014, 11:09 AM -
Converting KRV 2000, dimension from an XYZ required
By komatias in forum Machine DiscussionReplies: 2Last Post: 27-01-2014, 01:23 PM -
A little help for a newb please? :)
By WollyUK in forum Gantry/Router Machines & BuildingReplies: 3Last Post: 05-03-2012, 11:54 PM -
NEW MEMBER: Newb from Scotchland
By BigAl in forum New Member IntroductionsReplies: 3Last Post: 18-11-2011, 12:32 AM -
NEW MEMBER: Newb from Derbyshire
By Redccm in forum New Member IntroductionsReplies: 1Last Post: 02-01-2011, 10:00 AM
Bookmarks