. .
  1. #1
    Having worked in offices where this kind of A4 quick-reference was used it never occurred to me that lots of people may not be aware that they exist.


    A4 sheets are stored in double sided framed clear plastic folders which are easily leafed through to select the required information, the frames can be unclipped and taken to the machine or bench then clipped back in place when finished with, the paper is protected from dirt and damage.

    At around £25 for a 10 page unit they aren't cheap but they are brilliant way to store and access tapping charts, drill size equivalent charts, thread identification data etc. in a workshop where "every square inch counts",

    Regards,
    Nick
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	A4WallFile.jpg 
Views:	219 
Size:	71.9 KB 
ID:	18814  
    Last edited by magicniner; 29-06-2016 at 09:24 AM.
    You think that's too expensive? You're not a Model Engineer are you? :D

  2. The Following 2 Users Say Thank You to magicniner For This Useful Post:


  3. #2
    Where from Nick ? I can find an all black one on AliExpress for $40, which is £30 since this country has sipped from the poison chalice.

  4. #3
    good to know Nick
    I'm starting to compile A4 sheets for drill speeds tap sizes etc and was thinking about removing the front cover from a ring binder and screwing the back cover to the wall. This would leave the metal spring rings available to hold doc wallets or punched laminated sheets.
    Bit cheaper but not so slick and may not last so long
    Last edited by routercnc; 29-06-2016 at 05:17 PM.
    Building a CNC machine to make a better one since 2010 . . .
    MK1 (1st photo), MK2, MK3, MK4

  5. #4
    I can't find the link again for the one in the photo but it was £25 in the UK.
    Being able to lift out or replace a single page holder with greasy hands without fumbling and fiddling is fantastic.
    Mine were free from the skip, when Kraft closed the Sheffield based Cadbury Customer Contact Centre, I'd never seen them until I joined Cadbury IT Support.

    - Nick
    You think that's too expensive? You're not a Model Engineer are you? :D

  6. #5

  7. #6
    Good Man!
    I was almost tempted but have left them alone for someone who doesn't yet have one,
    ;-)
    Nick
    You think that's too expensive? You're not a Model Engineer are you? :D

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Establisihing reference for rail alignment
    By tropostudio in forum Gantry/Router Machines & Building
    Replies: 0
    Last Post: 14-05-2015, 08:28 PM
  2. Heidenhain ME 101 Tape reader or alternative program storage.
    By corkcnc in forum Machine Control Software
    Replies: 3
    Last Post: 19-03-2014, 11:28 AM
  3. Revised G-Code Quick-Reference / Cheat Sheet
    By DanielF in forum Machine Control Software
    Replies: 2
    Last Post: 20-02-2014, 11:14 AM
  4. Chip load chart
    By motoxy in forum Machine Discussion
    Replies: 1
    Last Post: 17-09-2012, 10:05 PM
  5. Schematic Symbol Reference
    By Lee Roberts in forum General Electronics
    Replies: 1
    Last Post: 23-01-2008, 03:23 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •