Activity Stream
-
Older Activity
-
2 Days AgoLeadhead started a thread Marchant Dice - Tonman Super drive input for probe. in Marchant Dice MachinesI have an old Marchant Dice CNC router with the Tonman Super drive controller. I would like to add a probe. Can I enquire if any members have made...0 replies | 251 view(s) -
4 Days AgoA_Camera started a thread My new mill. I went for the HBM BF 25 Vario in Milling Machines, Builds & ConversionsHello everyone! For a long time I wanted a real metal mill, but it was out of question because I had no space where I had my previous home....0 replies | 638 view(s)
-
1 Week Agoroutercnc replied to a thread Cheap milling machine spindle - BT30-ER20, air powered draw bar + Tear Down! in Tool & Tooling TechnologyThanks to JLCCNC for machining some of the parts used in this build: https://jlccnc.com/?from=routercnc Here is the next video if you are following...20 replies | 80744 view(s) -
1 Week AgoMuzzer replied to a thread Biting the Bullet, 1985 Matsuura V2 for refit in Classified Ads, Buy, Sell & SwapI'd love (another) one but my workshop is already beyond full capacity! Sounds like a great starting point for a quality conversion. As ever, the...2 replies | 2382 view(s)
-
1 Week Agograffian replied to a thread Biting the Bullet, 1985 Matsuura V2 for refit in Classified Ads, Buy, Sell & SwapNo one fancy a cheap bedmill.2 replies | 2382 view(s)
-
2 Weeks Agograffian started a thread Biting the Bullet, 1985 Matsuura V2 for refit in Classified Ads, Buy, Sell & SwapBought in 2007. Had great plans, never got round to them. I stripped all original electronics of it, so it fits in my garage. I bought some parts ...2 replies | 2382 view(s)
-
2 Weeks AgoGib strips are normally steel. I've made new ones in the past using gauge plate (ground flat stock)7 replies | 5075 view(s)
-
2 Weeks AgoRoutoutcnc still exists, but their website is only showing an Apache test page - http://www.routoutcnc.com/ They're still active on eBay (...1 replies | 3113 view(s)
-
2 Weeks AgoHi folks. Got given a machine that sat in a garage for a long while, trying to start it, help needed. Never played with Mach3 cnc's so at this...1 replies | 3113 view(s)
-
2 Weeks AgoI have a milling machine 800 watt and ER16 collet. Also a angled cutter of 60 degrees a good one. I want to rebuild the lathe complete, because it...7 replies | 5075 view(s)
-
2 Weeks AgoYes, you're right, it's just a matter of changing the belts. But since I'm going to replace the lathe motor with a 3-phase motor, and therefore won't...2 replies | 5226 view(s)
-
3 Weeks AgoFrom what I can see the drill already has 12 speeds set by the belt and pulleys. Though the inverter you have has single phase output which is rare...2 replies | 5226 view(s)
-
3 Weeks AgoI have an XSY AT2 frequency converter that is supposed to drive a 500-watt drill column. Drill column, TBD 500/2005 230 V, 50 Hz, 500 watts,...2 replies | 5226 view(s)
-
3 Weeks AgoAnd because that guide rib is heavily corroded, it is hardly possible to adjust it properly. The points of the adjustment screws must be placed...7 replies | 5075 view(s)
-
3 Weeks AgoWhat are the spindle bolts? Photo again please. What do you mean "fragile in size"? What you call a guide strip is usually called a "gib strip"...7 replies | 5075 view(s)
-
3 Weeks AgoThe guide strip is heavily corroded, as the photo also shows. The strip is also fragile in size, and the spindle bolts do not seem to have any grip.7 replies | 5075 view(s)
-
3 Weeks AgoMight be helpful if you could show us were they are located, so we can better help7 replies | 5075 view(s)
-
3 Weeks AgoDo you mean the gib strips? What is wrong with the existing ones?7 replies | 5075 view(s)
-
3 Weeks AgoHallo I want to upgrade my lathe Ferm 350, I found out that the adjustment strip are not so cool. It is very difficult to find new strips, so I have...7 replies | 5075 view(s)
-
3 Weeks AgoSold6 replies | 19606 view(s)
-
4 Weeks Agoshaunzor started a thread FOR SALE: Onefinity Elite Foreman 4x4 with 2.2kw spindle, laser etc in Items For Salehttps://www.ebay.co.uk/itm/227450868079 For sale is my Onefinity Elite Foreman 4ft x 4ft CNC machine. Comes with all the additional extras you...0 replies | 4472 view(s)
Marchant Dice - Tonman Super drive...