Activity Stream
-
Older Activity
-
2 Minutes AgoI doubt you'll get a secondhand one, as the spindle motor is a bit of a weak point. However not as much of a weak point as the controller normally...1 replies | 17 view(s) -
4 Minutes AgoIt would depend on if you're extending the stepper motor wiring, or the control signals to the motor. To the drive, you might get some...1 replies | 24 view(s)
-
54 Minutes AgoLooking for a standard motor from a CMD300 / X2 mill please1 replies | 17 view(s)
-
2 Hours AgoI have a non manufacture project I need a stepper for but it's low torque I'm just rotating a Lazy Susan but I need positional accuracy which I...1 replies | 24 view(s) -
1 Day AgoRick, All sorted. Regards.164 replies | 137188 view(s)
-
2 Days AgoHello, Been a while since I used emachine CAD, I updated to current latest version without knowing idk lose dxf exporting. Could I please have...164 replies | 137188 view(s)
-
2 Days AgoI need to replace one of the connectors to thwe Z axis stepper motor on my Fox Alien 4040 xe pro. I'm struggling to find the exact connector to be...0 replies | 820 view(s)
-
2 Days AgoJust a final report. I have fixed this issue, well sort of. It appears that the vfd forgot its settings somehow. Previously I was using the on...5 replies | 4714 view(s)
-
2 Days AgoLooks like a pretty generic 1.5KW water cooled 80mm diameter spindle. 400Hz means it'll be ~24'000 RPM. Getting one quickly is likely to be your...1 replies | 1143 view(s)
-
3 Days AgoHi all I have a heavily modded Denford Microrouter here (Mach3, Water cooled spindle). Unfortunately, it appears the spindle has died today. ...1 replies | 1143 view(s)
-
3 Days AgoSmokie555 replied to a thread Spindle pulley locked onto shaft! in Milling Machines, Builds & ConversionsI'll check if they are doubled up in the morning m_c, I wonder what the grub screws are there for? Def none on the side.2 replies | 1092 view(s)
-
3 Days AgoAre 100% sure there are no grubscrews on the side? And if there is, that they've not been doubled up?2 replies | 1092 view(s)
-
3 Days AgoSmokie555 started a thread Spindle pulley locked onto shaft! in Milling Machines, Builds & ConversionsHi, has anyone any experience with this spindle motor pulley on my Bridgeport Interact 1 series 2. I am changing the motor but wanted to reuse the...2 replies | 1092 view(s)
-
3 Days AgoKova replied to a thread WANTED: Dahlgren dsc2000 black box to drive Gryphon suregrave router in Items WantedHi thanks for your reply, Its hard to find any info on these machines, at least in regards to troubleshooting! Unfortunately my arduino skills run to...13 replies | 10945 view(s)
-
4 Days Agohello hope you doing well i have been working on my cnc for over 4 year today for no reason i am facing a problem that is when i load any file to...0 replies | 1060 view(s)
-
4 Days Agoi appear to be finding more issues than solutions at the moment!! just opened the black box at the back of the machine and noticed the below. ...17 replies | 3610 view(s)
-
4 Days Agoheres an interesting development. so when the z is at its height it would be machining at i get this z movement issue. if i lower the z right down...17 replies | 3610 view(s)
-
4 Days Agonow done this and its not made any difference17 replies | 3610 view(s)
-
5 Days AgoFinishing the main motor plate and starting the electronic test bed . . .87 replies | 126645 view(s) -
5 Days AgoJimmybristol started a thread FOR SALE: Lang technick fixturing - unused - suprlus to requirement in Items For SaleHello all, Clearing out, for some new projects…. Going to put this on this on ebay but I thought that I would see if any of this is of use to...0 replies | 1298 view(s)
-
5 Days AgoJimmybristol started a thread Hurco VM10 VMC Machining Centre. 4th Axis. Year 2009 - £12,500+VAT in Classified Ads, Buy, Sell & SwapAll, I have a Hurco VM10 VMC for sale.... if you prefer to buy via ebay I can send you a link.. Machine requires 3ph. Hurco VM10 £15,000 inc....0 replies | 1217 view(s)
-
5 Days AgoDenford Micromill in good condition. Bought from Pete on this forum nearly 2 years ago, not getting enough use so I'm making space for a lathe. ...0 replies | 1355 view(s)
-
1 Week AgoI wondered if you're getting issues from having the boards sitting on that pink bubblewrap. It's antistatic, hence may have some level of...17 replies | 3610 view(s)
-
1 Week Agono, it only happens when the spindle is on17 replies | 3610 view(s)
-
1 Week AgoI've tried grounding my cnc but problem still opccurs. Remove dust collector too just to rule that out. Grounding wiring.1 replies | 1868 view(s)
-
1 Week AgoAny chance that it is a coupling or pulley slipping? Engraving - especially if you are V-engraving - tends to generate a lot of Z movement which...17 replies | 3610 view(s)
-
1 Week AgoAll thoughts welcome17 replies | 3610 view(s)
-
1 Week AgoHi all. Running a job this morning on my FoxAlien 4040 xe pro and half way through the job my z axis reversed and instead of lifting up, dove down...1 replies | 1868 view(s)
-
1 Week AgoHi Guys Just a quick introduction. My name is Chris and I recently built myself a Queenbee system from Bulkman with a CNC xPRO V5 controller...0 replies | 2105 view(s)
-
1 Week AgoBikerDaily replied to a thread WANTED: Dahlgren dsc2000 black box to drive Gryphon suregrave router in Items WantedNo progress. Company in Ireland will look at it for £200, then there would be fox costs. We would need to post Scotland to Ireland etc . No...13 replies | 10945 view(s)
Sieg X2 / CMD300 Mini Mill motor...