Activity Stream
-
Older Activity
-
22 Hours Agolordchalfont replied to a thread FOR SALE: Jazz CNC JZR 9060 Router (Dean) with stand in Items For SaleHi RobertE Interested in the machine and would like to make an offer for it Couple of issues from my side I would like to see it in action before...1 replies | 4433 view(s) -
1 Day AgoReduced £1,250 ovno2 replies | 3188 view(s)
-
1 Day Ago2 replies | 3188 view(s)
-
1 Day AgoIt appears that my Star-mills are not as appealing as I thought they might be. Chat GPT has a lot to answer for. :( It is a difficult time to sell...4 replies | 3754 view(s)
-
2 Days AgoMuzzer replied to a thread CONVERSION: What is the Total Cost of Conversion (Excluding the Mill) in Conversion Build LogsFYI, "NEMA" simply means imperial (inch) dimensions in tenths of an inch, so a NEMA 17 motor has a 1.7" square face. Beyond that, it could be a...38 replies | 195877 view(s)
-
3 Days AgoUltraNC started a thread NEW MEMBER: New member interested in CNC and G-code in New Member IntroductionsHi, new member, Interested in CNC and G-code and CNC software. Currently writing free online tools for the CNC community. If you have a dodgy...0 replies | 141 view(s)
-
3 Days AgoBitterend replied to a thread CONVERSION: What is the Total Cost of Conversion (Excluding the Mill) in Conversion Build LogsYes I have. I have already replaced the X axis acme screw with a ballscrew to eliminate excess play and chatter, I now have to do the Y. In order to...38 replies | 195877 view(s)
-
3 Days AgoIndy4x replied to a thread CONVERSION: What is the Total Cost of Conversion (Excluding the Mill) in Conversion Build LogsHave you thought about converting your Harrison?38 replies | 195877 view(s)
-
4 Days AgoUltraNC started a poll Built a free G-code viewer with real cycle-time simulation. Try to break it. in Manufacturer NewsI've built a free G-code viewer that runs in the browser. It uses real motion control algorithms the same kind as your CNC controller. Set your...0 replies | 135 view(s)
-
6 Days AgoCNCScotland started a thread FOR SALE: Vertical CNC Machine - Scotland - Converted to steppers - controller required. £1499 in Items For SaleBridgeport Interact II Vertical CNC Machine - Converted to modern NEMA 34 stepper motors £1499 – Glasgow G209BT INC VAT! A bargin for a...0 replies | 768 view(s)
-
1 Week AgoI have read this. so is it possible to get the output from a hybrid stepper motor on to a DRO?9 replies | 16130 view(s)
-
1 Week Agoroutercnc replied to a thread Cheap milling machine spindle - BT30-ER20, air powered draw bar + Tear Down! in Tool & Tooling TechnologyI managed to fix the issues in the last video then it was on to the next set of problems. I've been making slow progress programming the code for...17 replies | 53643 view(s) -
1 Week AgoBitterend replied to a thread CONVERSION: What is the Total Cost of Conversion (Excluding the Mill) in Conversion Build LogsI have just read this. I have a Harrison milling machine, I would buy a cnc replacement if I could find something of similar size, but they are all...38 replies | 195877 view(s)
-
1 Week AgoI am new here. Where do i find my posts please0 replies | 889 view(s)
-
1 Week AgoFor Sale: Wabeco D3000E lathe. Selling with items as per photo. Please make me a reasonable offer. Happy to show it working in situ before...0 replies | 1307 view(s)
-
1 Week AgoI have just replaced an ACME feed screw with a ball-screw on a Harrison milling machine, and in the process have had to remove the table feed motor....0 replies | 811 view(s)
-
1 Week AgoI have read this thread with some interest. I have an old harrison milling machine, the slideways are fine but the screws/nuts are worn. I have just...9 replies | 16130 view(s)
-
1 Week AgoStressedwoodman replied to a thread Problems with mach3 and cslabs controller - jittering & losing connection frequently. in General DiscussionI have replaced my laptop with a Durabook - installed the same OS as before, but upgraded the CS labs firmware. Fingers crossed it seems to have...1 replies | 4553 view(s)
-
1 Week AgoHi, for an ER20/80mm spindle, I’d go with a good quality 2.2kW water-cooled model. They are generally much quieter and last significantly longer than...5 replies | 11959 view(s)
-
2 Weeks AgoI've been looking to sell some gear myself but after tracking several items on ebay etc. there seems little interest. It makes me wonder if people do...2 replies | 19411 view(s) -
2 Weeks AgoIs there no interest in this? It will be a shame to see it go to scrap!2 replies | 19411 view(s)
-
2 Weeks Agoroutercnc replied to a thread Cheap milling machine spindle - BT30-ER20, air powered draw bar + Tear Down! in Tool & Tooling TechnologyThe servo was back in stock so it was time to order it and test it out. It was all going well until it wasn't . . . .17 replies | 53643 view(s)
-
2 Weeks AgoFor sale my Warco Mill, fitted with X axis feed and DRO! Any test or inspection welcome, all mechanically sound. PE30 4 Comes with 2 x vices, 2...2 replies | 3188 view(s)
-
2 Weeks AgoI know what you mean! My machines use ISO30 and ISO40 tooling. ISO30 is more expensive and difficult to find than ISO40 - and ISO35 is truly a...4 replies | 3754 view(s)
-
2 Weeks AgoFair comment Muzzer on reflection. BT35 toolholder are very difficult to come by in the UK. Advert edited. Cheers Sparky4 replies | 3754 view(s)
-
2 Weeks AgoOoof. £750 for 15 toolholders. Let me think about that....4 replies | 3754 view(s)
-
3 Weeks Ago2 x starmills available £1,950 each. Both run off a ABAC compressor see attached (£450) 2 x airlines included. 4 outlets. Windows XP/Mach3/VR...4 replies | 3754 view(s)
-
3 Weeks AgoDepends on your budget and the kind of work you plan - no idea of either, so how long's a piece of string etc but if you want to run out of the box,...4 replies | 5184 view(s)
-
3 Weeks Agohttps://www.cnc4you.co.uk/Machines4 replies | 5184 view(s)
-
3 Weeks Agoyes i get that i have a need for the machine without the need to search parts etc i need to put one to work asap .. what would you suggest ?4 replies | 5184 view(s)
Jazz CNC JZR 9060 Router (Dean)...