Activity Stream
-
Older Activity
-
1 Day AgoI wondered if you're getting issues from having the boards sitting on that pink bubblewrap. It's antistatic, hence may have some level of...14 replies | 1140 view(s) -
1 Day Agono, it only happens when the spindle is on14 replies | 1140 view(s)
-
1 Day AgoI've tried grounding my cnc but problem still opccurs. Remove dust collector too just to rule that out. Grounding wiring.1 replies | 252 view(s)
-
2 Days AgoAny chance that it is a coupling or pulley slipping? Engraving - especially if you are V-engraving - tends to generate a lot of Z movement which...14 replies | 1140 view(s)
-
2 Days AgoAll thoughts welcome14 replies | 1140 view(s)
-
2 Days AgoHi all. Running a job this morning on my FoxAlien 4040 xe pro and half way through the job my z axis reversed and instead of lifting up, dove down...1 replies | 252 view(s)
-
3 Days AgoHi Guys Just a quick introduction. My name is Chris and I recently built myself a Queenbee system from Bulkman with a CNC xPRO V5 controller...0 replies | 485 view(s)
-
4 Days AgoBikerDaily replied to a thread WANTED: Dahlgren dsc2000 black box to drive Gryphon suregrave router in Items WantedNo progress. Company in Ireland will look at it for £200, then there would be fox costs. We would need to post Scotland to Ireland etc . No...12 replies | 9072 view(s)
-
4 Days AgoUmmm. He posted this ad almost ten years ago mate..10 replies | 12798 view(s)
-
4 Days AgoKova replied to a thread WANTED: Dahlgren dsc2000 black box to drive Gryphon suregrave router in Items WantedHi Brian, We have a DSC 2000 that is showing the same symptoms. Did you ever find a remedy to the issues you were having with yours? Thanks ...12 replies | 9072 view(s)
-
4 Days Agovideo https://youtu.be/stbWpra7O_4 so you can hear the z stepper moving the z axis14 replies | 1140 view(s)
-
4 Days Agonot been in the cabinet for a while, its still messy :hopelessness:14 replies | 1140 view(s)
-
5 Days AgoThis is positive news. I will see if I can find a manual for it online before I next have a chance to look at it. Thanks I will report back,...4 replies | 2869 view(s)
-
5 Days AgoThose tests would indicate that the wiring and the spindle appear to be OK. Might be worth trying a factory reset on the VFD.4 replies | 2869 view(s)
-
5 Days AgoThat potential cost is why I swapped my spindle motor for a servo.14 replies | 1140 view(s)
-
5 Days Agowell nearly original ;) original stepper drivers. cant get a photo till im back in workshop tomorrow now, its a bit messy inside be warned. ...14 replies | 1140 view(s)
-
5 Days AgoNot that original then. What stepper drivers are fitted? A photo of the control cabinet would probably be good. My thoughts to it having only...14 replies | 1140 view(s)
-
5 Days Agoall original so stepper and ESS running mach3 (PC) ive owned the machine for over 10 years now and not had this issue before, had many others....14 replies | 1140 view(s)
-
5 Days AgoStepper or Servo machine? Fanuc or PC control?14 replies | 1140 view(s)
-
5 Days Agoyes all original. its a difficult one to know where to start14 replies | 1140 view(s)
-
5 Days AgoSounds like interference is getting into the Z step/dir signals.. Is it still the original spindle?14 replies | 1140 view(s)
-
5 Days Agoso an update with spindle off and z in the air. if i move x and y around manually z doesnt change. if i start the spindle and dont touch...14 replies | 1140 view(s)
-
5 Days Agocan anyone offer any suggestions? got a triac VMC and its starting to have z height issues. i do a lot of engraving and i set the z to zero, do a...14 replies | 1140 view(s)
-
5 Days Agotalhauk replied to a thread What is your opinion of the CNC 6040 Router Machine ? in Chinese MachinesNice t o have such kind of information, looking forward to learn about the product deeply for technical knowledge.7 replies | 26571 view(s)
-
5 Days AgoIs this available right now, what if you have to ship outside of your country. What will be your shipping charges apart from the price of the product.10 replies | 12798 view(s)
-
6 Days AgoSmokie555 replied to a thread Bridgeport Interact spindle motor pulley won't come off! in Bridgeport Milling MachinesSorted out today with two bolts down the threaded holes :sneakiness:1 replies | 1012 view(s)
-
6 Days AgoJackie started a thread Replacing the stepper motor (Austausch des Schrittmotors) in Stepper & Servo MotorsWie wir alle wissen, werden Schrittmotoren häufig in CNC-Werkzeugmaschinen eingesetzt. Leider funktionierte mein Schrittmotor nicht mehr und ich...0 replies | 731 view(s)
-
1 Week AgoHi m_c Thanks for replying to my question, I managed to spare half an hour today to investigate a little bit. I have done a few continuity tests,...4 replies | 2869 view(s)
-
1 Week AgoHaving lost my business in june 2022 through no fault of my own I have been somewhat forced into semi retirement, this is not something I wanted to...0 replies | 895 view(s)
-
1 Week AgoI'll work out all the steps I took to figure it out and put it down on paper. Was quite simple in the end as these things usually are once you get...3 replies | 2599 view(s)
Triac Z height issues