Activity Stream
-
Older Activity
-
22 Hours AgoNice video. How is the machine now after a few years of use? Are you happy with it? Isn't 400W too weak? Just last week I bought a similar one, but...1 replies | 2917 view(s)
-
23 Hours AgoI think the answer to that should be it depends on what you are working with and want to extract. I mean, personally, I don't use any mechanical...1 replies | 6514 view(s)
-
23 Hours AgoI always wanted a metal band saw but never really got around buying one because I always thought these are special tools I rarely will use and are...0 replies | 270 view(s)
-
2 Days AgoAitch started a thread eBay: Sieg CNC cabinet, bare unit without milling machine, electronics or wiring in Items On eBay UKhttps://www.ebay.co.uk/itm/186707891419 Hi Sorry, I know this is a bit late in the day to be posting this but this may be of use to someone,...0 replies | 559 view(s)
-
4 Days AgoLee Roberts replied to a thread Compact THC 150 - problem with plasma cutting of sheet metal in Plasma Table MachinesSounds like a leak to me (interference perhaps?), check all your earth (ground) wires are secure, make sure no control and power wires are in close...1 replies | 2030 view(s)
-
4 Days AgoThey look OK, don't speak Polish You didn't say what you wanted machine wise so hard to judge and we buy 2nd hand mostly lol Just remember...1 replies | 1414 view(s)
-
5 Days AgoLmao, a "McWine" haha :applause::beer:8 replies | 5723 view(s)
-
5 Days AgoHi all, im looking into some new CNC machine manufacturers in Europe who can export to the UK and wanted to get your thoughts on this company. ...1 replies | 1414 view(s)
-
1 Week Agohi chris i just went with the makita router . thought i could always upgrade later if i needed it8 replies | 5723 view(s)
-
1 Week AgoX axis gantry, cheap linear rails quick look, new Z axis touch off (again!) and Y axis movement.9 replies | 11348 view(s)
-
1 Week AgoOops! Apologies I inserted the wrong link, the one I'm using has only one relay: ...4 replies | 4430 view(s)
-
1 Week AgoJBL_LG started a thread Compact THC 150 - problem with plasma cutting of sheet metal in Plasma Table MachinesHello. Voltage measurement value on the THC 150 screen changes. In the Mach3 torch control interface, the torch changes height. However, this is...1 replies | 2030 view(s)
-
1 Week AgoI have had a beer in McD's It was anti climatic It came in a can like a store I wanted a paper cup McD's beer!!!! Lithuania, they sold...8 replies | 5723 view(s)
-
1 Week AgoWait...what?!?!... McDonald's do wine? Red or White?8 replies | 5723 view(s)
-
1 Week AgoApologies for thread hijack, but perhaps John, or anyone using this ubiquitous board, can clear up a confusion with pins on the above board which I...4 replies | 4430 view(s)
-
1 Week AgoYoutube is your friend for what to do with it and upgrades Buy everything from Alixpress Good luck Honestly for this machine Vcarve is a...8 replies | 5723 view(s)
-
1 Week AgoI will do. I had an HPC CNC machine (from Halifax) for about 3 years and sold it in lockdown for almost twice what I paid for it. Due to health...8 replies | 5723 view(s)
-
1 Week AgoThanks Chris . Appreciate the offer, I may switch but as I have a years free subscription when I bought the onefinity I am just going through all the...8 replies | 5723 view(s)
-
1 Week AgoHello Dan. Im doing this a bit backwards. Im getting the software to master before I buy the CNC machine. Ive done down the route of Vectric...8 replies | 5723 view(s)
-
1 Week AgoThanks. Can you let me know an idea of pricing. Not specifically looking at the centroid servo motors however that might be of interest if you have...3 replies | 5923 view(s)
-
1 Week Agohere are some pictures3 replies | 5923 view(s)
-
1 Week AgoHi, I'm seeking mechanical & Electrical manual for below machine. Petewe PFS 30 CNC0 replies | 3650 view(s)
-
1 Week AgoToolpath can do it according to AXYZ I asked them, I did not ask them about using a switch lol as they want to sell the USB device so will say no...2 replies | 3916 view(s)
-
1 Week AgoCheers Andrew, I will post it there too, great advice as the more people who see it the better chance I'll have of getting help. Hi Chaz, yeah...3 replies | 4187 view(s)
-
2 Weeks AgoHi, can you share pics please - specifically interested in the spindle / toolchanger and a set of rails / ballscrews that I could use for a Z axis...3 replies | 5923 view(s)
-
2 Weeks AgoYou need to understand the modes. Position is step / direction. Speed is -10 to 10V. This is specific to the servo / driver and has nothing to do...3 replies | 4187 view(s)
-
2 Weeks AgoThere is no need for DNC if your controller works.It is only really justified if the controller is in poor order or if the file you are trying to run...2 replies | 3916 view(s)
-
2 Weeks AgoHi all is it possible to install a 4th axis on the axyz milenium, Recently bought a 3d scanner and am now interested in doing rotary...0 replies | 3589 view(s)
-
2 Weeks AgoHi Bud I have just purchased the Creality otter scanner and i really am impressed with it , not that i am an expert . far from it but i really am...4 replies | 38842 view(s)
-
2 Weeks AgoI want to run a 4010 and a 6010 Can I just use a DB9 switch to connect them both up and switch between them? I know I have to make my own cables...2 replies | 3916 view(s)
Benchtop 5" bandsaw from Warco