Activity Stream
-
Older Activity
-
16 Hours AgoAts101 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionPlease see photos for driver, control board and stepper set up. I'm hoping the photos will prompt some more thoughts into the matter. Many thanks.3 replies | 169 view(s)
-
22 Hours AgoAts101 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionHi John, Thank you for the reply - I have a copy of the A11 manual and have been through this multiple times. I will triple check the...3 replies | 169 view(s)
-
22 Hours AgoJohnHaine replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionTwo possible causes occur to me. One is that there is an intermittent connection in the z direction wire, but you seem to have ruled that out. The...3 replies | 169 view(s)
-
1 Day AgoDear all, I am new to this forum and looking for some advice about a current issue with my 8x4 CNC router. The machine is branded under the...3 replies | 169 view(s)
-
1 Day AgoHI Nicola. Welcome to the forum. You will need to provide more information. Pictures of the machine and control box might help. Also please...1 replies | 165 view(s)
-
1 Day AgoWelcome.1 replies | 136 view(s)
-
1 Day AgoThere are no lights on illuminated the left hand side. Although the open button is not lit it does still open the door. I suspected it might be a...1 replies | 165 view(s)
-
2 Days AgoI Have an Isel 4433 with a few issues.1 replies | 136 view(s)
-
4 Days AgoJohnHaine replied to a thread Wiring plan for upgrading my chinese cnc electrics enclosure, have I missed anything? in Gantry/Router Machines & BuildingMy estop is wired to remove power from the spindle drive and assert an estop condition to the controller - there should be an input on the AXBB to do...5 replies | 808 view(s)
-
4 Days Agopaul4523 replied to a thread Wiring plan for upgrading my chinese cnc electrics enclosure, have I missed anything? in Gantry/Router Machines & BuildingIm curious, how would you wire an e-stop so it turns off the drivers but still keeps the motors energised? The motors take their power from the...5 replies | 808 view(s)
-
5 Days Agomekanik replied to a thread Supported round rails and C5 ground ballscrew in Rails, Guideways & BearingsHi Dudz I don't have a machine but have done enough reading of the extensive knowledge available on the forum, IMO i think you would be better...1 replies | 663 view(s)
-
5 Days AgoI have 25mm supported round rails on all 3 axis of my CNC router (for aluminium) . At the moment I have 16mm C7 Chinese ballscrews. If I were to...1 replies | 663 view(s)
-
6 Days AgoPlease contact Caminix CNC Machinery(Zhejiang) Co.,Ltd for technical support for the ball valve grinding machine. You can send email to...1 replies | 5564 view(s)
-
6 Days AgoGracias por responder. Mi correo es [email protected] soy de argentina, de dónde eres tú?12 replies | 9429 view(s)
-
6 Days AgoJohnHaine replied to a thread Wiring plan for upgrading my chinese cnc electrics enclosure, have I missed anything? in Gantry/Router Machines & BuildingOn my lathe the e-stop turns off the drive and raises an E-stop condition on the controller. This halt execution but the drives remain energised and...5 replies | 808 view(s)
-
6 Days Agopaul4523 replied to a thread Wiring plan for upgrading my chinese cnc electrics enclosure, have I missed anything? in Gantry/Router Machines & BuildingThe latching stop and start buttons are to turn on and off the VFD and Drives. From what I've seen this seems to be a common setup. You are correct...5 replies | 808 view(s)
-
6 Days AgoJohnHaine replied to a thread Wiring plan for upgrading my chinese cnc electrics enclosure, have I missed anything? in Gantry/Router Machines & BuildingWhat's the reason for the stop/start button? Is it actually the E-stop? Normally it's useful to keep the stepper drives powered up even in an...5 replies | 808 view(s)
-
6 Days Agopaul4523 started a thread Wiring plan for upgrading my chinese cnc electrics enclosure, have I missed anything? in Gantry/Router Machines & BuildingUpgrading my OMIO X4 machine to an AXBB-E controller and new enclosure. I'm a novice and have tried to learn as much as possible in order to take on...5 replies | 808 view(s)
-
6 Days Agohttps://www.amazon.co.uk/Breakout-Controller-Control-Engraving-15-32VDC/dp/B084GPP44J/ref=sr_1_5?crid=1893MVWCXEGBZ&dib=eyJ2IjoiMSJ9.Lvwp1QoEu02_DVMHD...2 replies | 841 view(s)
Help diganosing fault with chinese...