Activity Stream
-
Older Activity
-
3 Hours Agodudz replied to a thread Supported round rails and C5 ground ballscrew in Rails, Guideways & BearingsSupported round rails. I know they are better, just wasnt sure how much better3 replies | 905 view(s)
-
4 Hours Agopippin88 replied to a thread Supported round rails and C5 ground ballscrew in Rails, Guideways & BearingsNo point going with expensive screws and keeping round rails. Profile / square linear bearings are FAR superior to round rails3 replies | 905 view(s)
-
14 Hours AgoI am thinking about doing this to my chinese CNC. Where would you place the linear tool holder rack so it does not take up working area space? ...32 replies | 39200 view(s)
-
16 Hours AgoAts101 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionUPDATE: I swapped X motor driver with the Z motor driver. I have not yet been able to reproduce the homing the wrong way issue BUT I repeated...4 replies | 306 view(s)
-
1 Day AgoAts101 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionPlease see photos for driver, control board and stepper set up. I'm hoping the photos will prompt some more thoughts into the matter. Many thanks.4 replies | 306 view(s)
-
1 Day AgoAts101 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionHi John, Thank you for the reply - I have a copy of the A11 manual and have been through this multiple times. I will triple check the...4 replies | 306 view(s)
-
2 Days AgoJohnHaine replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionTwo possible causes occur to me. One is that there is an intermittent connection in the z direction wire, but you seem to have ruled that out. The...4 replies | 306 view(s)
-
2 Days AgoDear all, I am new to this forum and looking for some advice about a current issue with my 8x4 CNC router. The machine is branded under the...4 replies | 306 view(s)
-
2 Days AgoHI Nicola. Welcome to the forum. You will need to provide more information. Pictures of the machine and control box might help. Also please...1 replies | 270 view(s)
-
2 Days AgoWelcome.1 replies | 215 view(s)
-
2 Days AgoThere are no lights on illuminated the left hand side. Although the open button is not lit it does still open the door. I suspected it might be a...1 replies | 270 view(s)
-
3 Days AgoI Have an Isel 4433 with a few issues.1 replies | 215 view(s)
-
5 Days AgoJohnHaine replied to a thread Wiring plan for upgrading my chinese cnc electrics enclosure, have I missed anything? in Gantry/Router Machines & BuildingMy estop is wired to remove power from the spindle drive and assert an estop condition to the controller - there should be an input on the AXBB to do...5 replies | 1090 view(s)
-
5 Days Agopaul4523 replied to a thread Wiring plan for upgrading my chinese cnc electrics enclosure, have I missed anything? in Gantry/Router Machines & BuildingIm curious, how would you wire an e-stop so it turns off the drivers but still keeps the motors energised? The motors take their power from the...5 replies | 1090 view(s)
-
6 Days Agomekanik replied to a thread Supported round rails and C5 ground ballscrew in Rails, Guideways & BearingsHi Dudz I don't have a machine but have done enough reading of the extensive knowledge available on the forum, IMO i think you would be better...3 replies | 905 view(s)
Supported round rails and C5...