Activity Stream
-
Older Activity
-
3 Weeks AgoHey Folks, I'd like to rip out the interior of a boat and refit it utilising the CNC for all the woodwork. Ideally I'd like to CAD it out...2 replies | 1991 view(s)
-
1 Week Agopaul4523 started a thread Wiring plan for upgrading my chinese cnc electrics enclosure, have I missed anything? in Gantry/Router Machines & BuildingUpgrading my OMIO X4 machine to an AXBB-E controller and new enclosure. I'm a novice and have tried to learn as much as possible in order to take on...5 replies | 1338 view(s)
-
2 Weeks AgoI just bought and it's really good 300 on Amazon if you apply the voucher Printing now at 600mm/s with no issues, super nice quality A...0 replies | 1895 view(s)
-
3 Days AgoDear all, I am new to this forum and looking for some advice about a current issue with my 8x4 CNC router. The machine is branded under the...10 replies | 473 view(s)
-
1 Week AgoHello It has been a couple of years since I built my lathe and mill, and have picked up another lathe recently to convert. A lot seems to have...2 replies | 1253 view(s)
-
1 Week AgoI have 25mm supported round rails on all 3 axis of my CNC router (for aluminium) . At the moment I have 16mm C7 Chinese ballscrews. If I were to...3 replies | 1079 view(s)
-
3 Days AgoThere are no lights on illuminated the left hand side. Although the open button is not lit it does still open the door. I suspected it might be a...1 replies | 377 view(s)
-
4 Days AgoI Have an Isel 4433 with a few issues.1 replies | 286 view(s)
-
18 Hours AgoI'm just finishing a retrofit of a Triac. Used Acorn Centroid. Previously I've used SZGH, CS LABS, Pokeys and various hardware on Mach 3 and Mach...1 replies | 76 view(s)
-
13 Hours AgoTnW started a thread 8x4 CNC Router Build - Wood/Steel or Steel Frame and Component Advice in Gantry/Router Machines & BuildingAfternoon! I'm looking to build/rebuild my 8x4 CNC. I currently use one of the SheetCNC routers, it's a 25mm MDF frame which is chain-driven and...0 replies | 68 view(s)
-
1 Day AgoMuch of the internet seems to indicate that VFDs will cause RCD systems to trip out. In the UK though the whole building tends to be protected with...0 replies | 22 view(s)
-
55 Minutes AgoAnyone know anything about these ? Are they worth the money ?. In this case 5K in pounds ...0 replies | 13 view(s)
-
5 Hours AgoI still use Emachineshop ( old version). I have yet to find such a simple to use CAD programme (free or for purchase). Just wish the 3D preview would...175 replies | 194480 view(s)
-
7 Hours AgoFor multi-axis, a key thing to look at is how tool offset compensation is handled. Not all controllers can handle it for 4/5th axis, and rely on it...1 replies | 76 view(s)
-
17 Hours AgoAts101 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionAwesome stuff. I will keep updating the tread. A10 replies | 473 view(s)
-
17 Hours Agophill05 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionYes picked up a new card from cnc4you put a copy of mach on and away we went10 replies | 473 view(s)
-
17 Hours AgoAts101 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionThanks, Yes I wouldn't be overly surprised if the issues persist after replacing the driver but I am confident it will sort out my problem. If...10 replies | 473 view(s)
-
18 Hours Agophill05 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionMuch like your problem we tried changing drivers round but still had the problems, we took out the dsp and replaced the card to try Mach 3 and it...10 replies | 473 view(s)
-
19 Hours AgoAts101 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionAbout 30 mins ago, turned on the machine, homed all axes and X moved in the positive direction rather than negative. Fault diagnosed as driver and I...10 replies | 473 view(s)
-
19 Hours AgoHi. Would it be possible for me to gain access to an old copy? Not sure how this works but I see people previous entered an email address. ...175 replies | 194480 view(s)
-
19 Hours Agophill05 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionNot had driver problems but quite a few years ago had DSP problems at the time I did away with dsp changed to Mac3 controller never had a problem...10 replies | 473 view(s)
-
1 Day Agodudz replied to a thread Supported round rails and C5 ground ballscrew in Rails, Guideways & BearingsSupported round rails. I know they are better, just wasnt sure how much better3 replies | 1079 view(s)
-
1 Day Agopippin88 replied to a thread Supported round rails and C5 ground ballscrew in Rails, Guideways & BearingsNo point going with expensive screws and keeping round rails. Profile / square linear bearings are FAR superior to round rails3 replies | 1079 view(s)
-
1 Day AgoI am thinking about doing this to my chinese CNC. Where would you place the linear tool holder rack so it does not take up working area space? ...32 replies | 39402 view(s)
-
1 Day AgoAts101 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionUPDATE: I swapped X motor driver with the Z motor driver. I have not yet been able to reproduce the homing the wrong way issue BUT I repeated...10 replies | 473 view(s)
-
2 Days AgoAts101 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionPlease see photos for driver, control board and stepper set up. I'm hoping the photos will prompt some more thoughts into the matter. Many thanks.10 replies | 473 view(s)
-
2 Days AgoAts101 replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionHi John, Thank you for the reply - I have a copy of the A11 manual and have been through this multiple times. I will triple check the...10 replies | 473 view(s)
-
2 Days AgoJohnHaine replied to a thread Help diganosing fault with chinese Chinese CNC router in General DiscussionTwo possible causes occur to me. One is that there is an intermittent connection in the z direction wire, but you seem to have ruled that out. The...10 replies | 473 view(s)
-
3 Days AgoHI Nicola. Welcome to the forum. You will need to provide more information. Pictures of the machine and control box might help. Also please...1 replies | 377 view(s)
-
3 Days AgoWelcome.1 replies | 286 view(s)
Storebro CNC Combi Mill