Tom J
22-02-2016, 11:00 PM
Hi Folks
Recently decided to use USB on my desktop router. I did not have enough funds to buy Ethernet CSMIO-IP-A or M.
So I end up with having this 3 axis HXC Motion Card.
Pic.1.
17679
Here is full details:
http://www.cdxhctech.com/html/eProduct/view_263.html
Card is plug and play easy to install, plug in too, however I have few issue with Mach3 configuration.
There is lack of proper set up info. Manual is poor and misleading - will say why and what.
Let me describe what I've achieved so far.
I managed quickly wire Nema 23 via DM542A and they work quiet, smooth, and quite cold.
I do run spindle water cooled 2.2kW - via PWM 0-10V signal to LG inverter.
I revised this post after reading Jazz replay.
Here are my issues:
- there are 8 outputs in the card, they start from OUT-0 and finish OUT-7.
Mach 3 doesn't list Output #0, so Output #1 with Pin 0 is OUT -0 a bit confusing, usually output number has the same pin number.
Because OUT-0 is not listed than we can not set it in spindle setup, for clockwise (M3).
I did not pay attention to the picture 2 (blue line, 2xNO contacts from common DCM-digital ground).
I simply tried to get low or high signal out from OUT 0&1.
To prove that picture is correct I tested with few mA signal I found that this contact between DCM - OUT.0 and DCM -OUT.1 exist and can be activated in Output signals as Out 1 & 2 pin 0 & 1.
Pic.2.
17709
Manual did not clearly state that - just picture.
On this stage I can start my spindle FRW (CW) from Mach by pressing: F5, spindle button or typing M3.
Q1.
Is there any other way to activate CCW rather than typing command M4 which can only be disable by M5 or reset (Thanks Jazz for reminding)
Q2.
Same problem with Mist M7 - any other way to activate rather than command M7?
Pic.3.
17678
- discovered one big problem which is not described:
Do not connect anything to outputs 0-7 unless output is enabled in control output menu, otherwise reset button will activate all outputs - make the relays live (This is big inconvenience and safety concern)
- another miss information, picture 4 shows blue line which connect 'Power In 6-36V' to 6-36V on input control port.
There is no internal connection - '6-36V input port' is isolated. No info regard that, only misleading picture.
This arrangement is not made, so extra connection is needed.
However 0V from 'Power In' is connected to 0V output control - see picture below
Pic.4.
17681
Q3.
How to set Input pin to set Out like in the logic controller?
for example Input 6 activates Output 6 or similar?
I did not have any problem with other DB board running via LPT1 port, and I can program PLC too, using ladder logic.
Q4.
The last problem I spotted is that I can not change motor tuning on spindle page- no blue graph. Motors ok, only spindle. Any Ideas?
Thanks in advance for any help, not so much info regard this particular model
Tom
Recently decided to use USB on my desktop router. I did not have enough funds to buy Ethernet CSMIO-IP-A or M.
So I end up with having this 3 axis HXC Motion Card.
Pic.1.
17679
Here is full details:
http://www.cdxhctech.com/html/eProduct/view_263.html
Card is plug and play easy to install, plug in too, however I have few issue with Mach3 configuration.
There is lack of proper set up info. Manual is poor and misleading - will say why and what.
Let me describe what I've achieved so far.
I managed quickly wire Nema 23 via DM542A and they work quiet, smooth, and quite cold.
I do run spindle water cooled 2.2kW - via PWM 0-10V signal to LG inverter.
I revised this post after reading Jazz replay.
Here are my issues:
- there are 8 outputs in the card, they start from OUT-0 and finish OUT-7.
Mach 3 doesn't list Output #0, so Output #1 with Pin 0 is OUT -0 a bit confusing, usually output number has the same pin number.
Because OUT-0 is not listed than we can not set it in spindle setup, for clockwise (M3).
I did not pay attention to the picture 2 (blue line, 2xNO contacts from common DCM-digital ground).
I simply tried to get low or high signal out from OUT 0&1.
To prove that picture is correct I tested with few mA signal I found that this contact between DCM - OUT.0 and DCM -OUT.1 exist and can be activated in Output signals as Out 1 & 2 pin 0 & 1.
Pic.2.
17709
Manual did not clearly state that - just picture.
On this stage I can start my spindle FRW (CW) from Mach by pressing: F5, spindle button or typing M3.
Q1.
Is there any other way to activate CCW rather than typing command M4 which can only be disable by M5 or reset (Thanks Jazz for reminding)
Q2.
Same problem with Mist M7 - any other way to activate rather than command M7?
Pic.3.
17678
- discovered one big problem which is not described:
Do not connect anything to outputs 0-7 unless output is enabled in control output menu, otherwise reset button will activate all outputs - make the relays live (This is big inconvenience and safety concern)
- another miss information, picture 4 shows blue line which connect 'Power In 6-36V' to 6-36V on input control port.
There is no internal connection - '6-36V input port' is isolated. No info regard that, only misleading picture.
This arrangement is not made, so extra connection is needed.
However 0V from 'Power In' is connected to 0V output control - see picture below
Pic.4.
17681
Q3.
How to set Input pin to set Out like in the logic controller?
for example Input 6 activates Output 6 or similar?
I did not have any problem with other DB board running via LPT1 port, and I can program PLC too, using ladder logic.
Q4.
The last problem I spotted is that I can not change motor tuning on spindle page- no blue graph. Motors ok, only spindle. Any Ideas?
Thanks in advance for any help, not so much info regard this particular model
Tom