View Full Version : WANTED: Easy change collets
mortenl
10-04-2016, 05:39 PM
Hi, I would like to buy some easy change Collets for my denford novamill, If you have any please make me an offer.
Regards Morten
magicniner
10-04-2016, 08:07 PM
If it's the holders you need Coventry Engineering still supply them.
http://www.coveng.co.uk/group/coventry-toolholders/products/toolholders-for-manual-machines/easy-change.html
cncJim
12-04-2016, 01:26 PM
I have also been on the look out but not found anything second hand.
This place sells them, not cheap though:-
http://www.engineeringsupplies.co.uk/tool-holders-easy-change-c-175.html?menu=1
Do you already have a selection of easychange holders? If not, it may be a cheaper option to swap out the easychange system (sell it) for a standard ER32 holder and a selection of collets?
Another option would be just to buy a easychange ER32 collet chuck (~£80 on the above link) and a selection of collets?
Cheers,
Jim
JohnHaine
12-04-2016, 11:06 PM
Morgen, I have an Easychange bt30 holder with two ER16 collet chucks that fit it, off my Novamill. Would this be interesting? I use straight er16 chucks in my machine. I'd prefer to sell as a job lot, they don't get used.
Sent from my iPad using Tapatalk
mortenl
13-04-2016, 07:23 PM
JohnHaine, PM send.
magicniner
14-04-2016, 11:50 AM
This place sells them, not cheap though:-
http://www.engineeringsupplies.co.uk/tool-holders-easy-change-c-175.html?menu=1
Thanks for the reminder Jim!
My little mill came with a 6mm endmill holder and a 10mm endmill holder, I've been using ER11 collet chucks on 10mm straight shanks (about £7 each on ebay) for 0-7mm tool holding.
I've just ordered an extra 10mm holder and a 12mm holder for ER16 collet chucks on 12mm straight shanks (about £10 each on ebay) to expand the range of tooling I can use,
Regards,
- Nick
Storeman
28-10-2016, 02:54 PM
I have also been on the look out but not found anything second hand.
This place sells them, not cheap though:-
http://www.engineeringsupplies.co.uk/tool-holders-easy-change-c-175.html?menu=1
Do you already have a selection of easychange holders? If not, it may be a cheaper option to swap out the easychange system (sell it) for a standard ER32 holder and a selection of collets?
Another option would be just to buy a easychange ER32 collet chuck (~£80 on the above link) and a selection of collets?
Cheers,
Jim
Try here:-- http://www.jurassictools.com/store/search?search=store&phrase=easy+change
magicniner
30-10-2016, 12:35 PM
Try here:-- http://www.jurassictools.com/store/search?search=store&phrase=easy+change
Good call! I've dealt extensively with Tony through eBay and have also used his website and have always been pleased with the quality and service,
Regards,
Nick
Jonathan
30-10-2016, 03:31 PM
Hi, I would like to buy some easy change Collets for my denford novamill, If you have any please make me an offer.
Regards Morten
I have quite a few, from a denford "Easimill", at least 6 I think. Let me know if you're interested and I'll check what sizes they are.
Powered by vBulletin® Version 4.2.5 Copyright © 2025 vBulletin Solutions Inc. All rights reserved.