. .

Home: Motor Drivers & Controllers

Discuss everything related to motor drivers and controllers here.

Page 11 of 19 FirstFirst ... 910111213 ... LastLast
Threads 201 to 220 of 365

  1. Sticky Thread Sticky: eBay TB6560 Stepper Motor Driver Boards

    Started by Mad Professor, 03-11-2009
    boards, driver, ebay, motor, stepper, tb6560 14 Attachment(s)
    • Replies: 127
    • Views: 579,336
    dazp1976
    22-08-2018 Go to last post

  1. Question Stepper Motor Driver - cheap similar to ArcEuro 4.2A Bi-Polar Stepper Motor Driver

    Started by craynerd, 16-03-2014
    • Replies: 1
    • Views: 30,130
    Jonathan
    16-03-2014 Go to last post

  2. Anyone recommend motor drive amplifer boards????

    Started by Davek0974, 31-01-2014
    • Replies: 4
    • Views: 9,980
    Davek0974
    13-02-2014 Go to last post

  3. CW8060 or alternative?

    Started by Tenson, 03-02-2014
    • Replies: 4
    • Views: 10,017
    Tenson
    03-02-2014 Go to last post

  4. Calibration issues, advice needed

    Started by Kernow Jim, 18-01-2014
    • Replies: 16
    • Views: 43,176
    Kernow Jim
    23-01-2014 Go to last post

  5. Stepper driver voltages - using different levels

    Started by routercnc, 08-01-2014
    • Replies: 15
    • Views: 92,714
    Clive S
    11-01-2014 Go to last post

  6. Digital Drivers and Stall Detection

    Started by Washout, 10-12-2013
    • Replies: 6
    • Views: 16,474
    Washout
    10-12-2013 Go to last post

  7. Question clunks / missing steps - DM856 and single pulse operation

    Started by dsc, 13-10-2013
    3 Attachment(s)
    • Replies: 37
    • Views: 103,577
    dsc
    09-12-2013 Go to last post

  8. Leadshine 4-axis motor motion control cards? Any experience and info?

    Started by Boyan Silyavski, 02-12-2013
    • Replies: 0
    • Views: 14,159
    Boyan Silyavski
    02-12-2013 Go to last post

  9. M542 driver - motor vibration at low speeds

    Started by birchy, 18-11-2013
    17 Attachment(s)
    • Replies: 34
    • Views: 75,919
    EddyCurrent
    22-11-2013 Go to last post

  10. Help withController dip switch settings and Mach3 motor tuning

    Started by liamo1991, 14-11-2013
    2 Attachment(s)
    • Replies: 2
    • Views: 41,485
    JAZZCNC
    15-11-2013 Go to last post

  11. Stepper controller to manually input a specific degree

    Started by Web Goblin, 12-10-2013
    • Replies: 11
    • Views: 154,463
    irving2008
    13-10-2013 Go to last post

  12. USB breakout boards from China

    Started by asbo, 07-10-2013
    • Replies: 0
    • Views: 7,919
    asbo
    07-10-2013 Go to last post

  13. Servo fault handling

    Started by m_c, 23-09-2013
    • Replies: 0
    • Views: 8,165
    m_c
    23-09-2013 Go to last post

  14. Geck 540 motor drivers??

    Started by gerrymoore, 21-09-2013
    7 Attachment(s)
    • Replies: 18
    • Views: 24,171
    gerrymoore
    22-09-2013 Go to last post

  15. Are VFD 0-10V inputs isolated or tied to gnd?

    Started by m_c, 21-09-2013
    • Replies: 3
    • Views: 10,130
    birchy
    21-09-2013 Go to last post

  16. Wiring Steppers to controllers

    Started by liamo1991, 04-09-2013
    cnc, controller, project, stepper, wiring 3 Attachment(s)
    • Replies: 1
    • Views: 13,232
    JAZZCNC
    05-09-2013 Go to last post

  17. AM882 works with Protune - but not with the ZPA5-INT BOB

    Started by badgerman, 26-08-2013
    2 Attachment(s)
    • Replies: 19
    • Views: 20,608
    JAZZCNC
    01-09-2013 Go to last post

  18. Axis random freezing with SS=2H044MA stepper drivers??

    Started by gerrymoore, 29-08-2013
    • Replies: 7
    • Views: 13,183
    gerrymoore
    01-09-2013 Go to last post

  19. Chinese 2.2 water cooled spindle / Which VFD ?

    Started by dudz, 03-11-2012
    • Replies: 20
    • Views: 34,817
    stuboy
    16-08-2013 Go to last post

  20. breakout board usb or parallel

    Started by crossleymarko, 08-04-2012
    • Replies: 13
    • Views: 32,127
    Nugget
    30-07-2013 Go to last post
Page 11 of 19 FirstFirst ... 910111213 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules