. .

Home: General Discussion

General Discussion for anything not related to or covered by our other forums.

Page 6 of 65 FirstFirst ... 456781656 ... LastLast
Threads 101 to 120 of 1293

  1. Poll Sticky Thread Sticky: Poll: Feedback poll - which age group are you?

    Started by mocha, 26-04-2012
    7 Pages •
    1 2 3 ... 7
    • Replies: 66
    • Views: 333,575
    The Gresley Luthier
    22-02-2026 Go to last post

  2. Sticky Thread Sticky: Merry Christmas & Happy New Year 2010 - 2025

    Started by Wobblybootie, 25-12-2010
    12 Pages •
    1 2 3 ... 12
    4 Attachment(s)
    • Replies: 119
    • Views: 319,238
    EddyCurrent
    07-01-2026 Go to last post

  3. Sticky Thread Sticky: John Stevenson

    Started by m_c, 23-10-2017
    3 Pages •
    1 2 3
    • Replies: 20
    • Views: 108,519
    Lee Roberts
    18-02-2020 Go to last post

  1. workbee tramming

    Started by Andrew C, 02-07-2022
    • Replies: 1
    • Views: 6,366
    JAZZCNC
    02-07-2022 Go to last post

  2. stencil film

    Started by Andrew C, 27-06-2022
    • Replies: 1
    • Views: 3,212
    Lee Roberts
    01-07-2022 Go to last post

  3. Surfacing burn

    Started by Andrew C, 01-07-2022
    • Replies: 1
    • Views: 2,504
    Clive S
    01-07-2022 Go to last post

  4. Plywood parts on CNC for aviation project

    Started by marianmadalin91, 22-06-2022
    1 Attachment(s)
    • Replies: 0
    • Views: 2,461
    marianmadalin91
    22-06-2022 Go to last post

  5. Air flow

    Started by erniehatt, 25-05-2022
    2 Pages •
    1 2
    2 Attachment(s)
    • Replies: 16
    • Views: 16,206
    Muzzer
    01-06-2022 Go to last post

  6. Touch probe problem

    Started by Andrew C, 27-05-2022
    • Replies: 1
    • Views: 5,592
    phill05
    27-05-2022 Go to last post

  7. Damping Test of Concrete & Steel Tube

    Started by Tenson, 02-07-2020
    2 Pages •
    1 2
    8 Attachment(s)
    • Replies: 11
    • Views: 122,766
    Bongo
    16-05-2022 Go to last post

  8. Cuts are offline

    Started by Andrew C, 15-05-2022
    • Replies: 6
    • Views: 8,489
    Andrew C
    15-05-2022 Go to last post

  9. vfd to spindle cable ?

    Started by voyager1972, 09-05-2022
    • Replies: 1
    • Views: 3,232
    EddyCurrent
    09-05-2022 Go to last post

  10. 800Hz single phase vfd

    Started by Bongo, 19-09-2021
    4 pole, high frequency, vfd
    • Replies: 7
    • Views: 17,418
    Voicecoil
    06-05-2022 Go to last post

  11. Aliexpress and JNet delivery

    Started by m_c, 07-01-2020
    2 Pages •
    1 2
    • Replies: 14
    • Views: 24,825
    JAZZCNC
    23-04-2022 Go to last post

  12. Back after a few years ... Mach3 Question please

    Started by dudz, 18-04-2022
    • Replies: 1
    • Views: 3,125
    RobC
    20-04-2022 Go to last post

  13. Milling Plastazote LD33 closed cell Foam - Any milling advice?

    Started by Zeeflyboy, 05-03-2017
    2 Pages •
    1 2
    • Replies: 17
    • Views: 55,971
    tomtailford
    06-04-2022 Go to last post

  14. Very mysterious dropping steps on one Y axis motor...I'm starting to lose it!!

    Started by Hatchett Job, 26-03-2022
    3 Pages •
    1 2 3
    • Replies: 25
    • Views: 112,395
    Hatchett Job
    01-04-2022 Go to last post

  15. Unusual sizes Raw 303 Stainless Stock suppliers in UK

    Started by Simtech, 21-03-2022
    • Replies: 2
    • Views: 6,690
    m.i.k.e
    22-03-2022 Go to last post

  16. Generic Pneumatics question.

    Started by Nemo1966, 11-03-2022
    1 Attachment(s)
    • Replies: 2
    • Views: 5,473
    Nemo1966
    11-03-2022 Go to last post

  17. 380v Output Inverter Braking.

    Started by Zadig, 03-03-2022
    2 Pages •
    1 2
    2 Attachment(s)
    • Replies: 16
    • Views: 18,213
    Zadig
    08-03-2022 Go to last post

  18. Question 1 signal two stepper drives

    Started by jmh474, 17-02-2022
    akz250, signal, stepper motors
    • Replies: 5
    • Views: 5,590
    dazp1976
    18-02-2022 Go to last post

  19. CNC auction Essex ending tomorrow

    Started by Desertboy, 07-02-2022
    • Replies: 1
    • Views: 2,926
    Muzzer
    07-02-2022 Go to last post

  20. no power to stepers

    Started by Mikes Planes, 02-02-2022
    • Replies: 5
    • Views: 3,732
    dazp1976
    03-02-2022 Go to last post
Page 6 of 65 FirstFirst ... 456781656 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules