Printable View
Hi All
I know its been a while since i posted but have been to busy loosing money:tennis: ( may as well tell it how it is )
But i was wondering if anyone on here knows of anyone on here that converts pictures to 3D STL relief models to be carved on the cnc
Pete
if your not after a freebie have a look at his work in the link..i don't what his rates are.
http://www.mycncuk.com/threads/5972-...ighlight=veres
Not quite sure what you are looking to do, but PhotoVCarve from Vectric will take pictures and produce "relief" toolpaths. You need to look at the website to see what it can do. Commercial product (i.e. it costs) but free trial available.
I have used 123D Catch to convert a set of photographs of an object to a 3S STL model, then used a freeware programme to turn it into a toolpath. 123D Catch is a free online "service" where you upload your photographs and some time later download a model. I found it difficult to use, but it did work and I took a series of images of an object right through to a machined piece. I think I used Pycam for the 3D toolpath generation although I'm not sure about that now; these days I use the Vectric Cut3D programme (but that one costs as well).
Cheers bud I will check out the link , I dont want a freebe as i need to pass the cost on to the client for this work to be done PeteQuote:
Originally Posted by deisel
Hi Bud
I have the Cut 3d program and the Vectric 3D but it does not convert a photo to a 3d relief does it ?
Pete
Quote:
Originally Posted by Neale
Have a look at Vectric PhotoVcarve will do all you want.
Phill
Will have a look :smug:Quote:
Originally Posted by phill05
No - that's what PhotoVCarve does. I had suggested a couple of ideas but they do very different things. Sorry if my post was confusing.Quote:
Originally Posted by petesos
Cheers bud I will go and have a look at that and see where it leads meQuote:
Originally Posted by Neale
Pete
That from the link above seems to me like top quality jobs. Being myself an artist, have done myself a couple of things in the past, so i could spot the good stuff.
Hi Bud
Is this a job you could do
Pete
Had a look at this program yes it does photos but I have a 80 watt Laser that does my photos far better quality than a cnc but the customer wants the Lancaster Bomber to look as though it is flying out of the wall :hopelessness:Quote:
Originally Posted by phill05
Pete
But your question was about getting an image through to cnc!! To get the best out of photoVcarve Use the highest resolution photos you have, first run through an Image edditing program & increase the contrast, then convert them to black and white (not gray scale).Quote:
Originally Posted by petesos
If you want to make a part of the image stand out more then you are going have to put some work into it to raise or lower said part, then you are looking at using another program such as Vertric ASPIRE in which you import an image work on it and take it through to produce the toolpaths for cutting on a cnc or laser, but going this route is expencive but rewarding in the finished piece.
Phill
Right Phill, I am going to have another go with it and do what you have said ,,,worth a try and will post the outcome BudQuote:
Originally Posted by phill05
Pete
From what you are saying, you might be looking to turn a picture into a 3D model, rather than the light-and-shade conversion that PhotoVCarve does. This is something I did a while back - I can't pretend that it's good, but it's better than I expected. It's part of a project to make a nameplate for my house. I used 123D Catch to turn a bunch of digital photographs of the badger model into an STL model which I then hacked around a bit, and used Cut3D to turn into a toolpath. It was all done when I was new to the software and the whole CNC thing, so it's not done very well, but it illustrates the art of the possible, maybe. I could imagine using this technique to get an impression of an aircraft emerging from a flat plate.
Original model:
Attachment 15486
Machined model:
Attachment 15487
The grooving effect is because I didn't use an appropriate step-over for the ballnose cutter used for finishing. As I say, it's not good but even to achieve this was a lot of work. I guess you might be able to find someone with 3D scanning capability, given an aircraft model as a starting point.
So you would like to do it by cutting or by laser, i don't understand?
Cause if by laser you need to retouch the file in Photoshop and make it look beveled
Or you need to make it a real 3D with Aspire or similar.
This bike is worked through Aspire and cut into a stone memorial.
http://www.mycncuk.com/attachment.ph...id=15488&stc=1
http://www.mycncuk.com/attachment.ph...id=15489&stc=1
Not bad Bud and we all need to start somewhere , when I tried it in photo v carve a while ago it looked like Road kill , HonestlyQuote:
Originally Posted by Neale
Hi Bud yes I want to make it a 3D carving but my skill level is not up to it:blue:Quote:
Originally Posted by silyavski
Hi BudQuote:
Originally Posted by phill05
Is this one you have done ??
Pete
Yes it's cut into a Portland stone memorial and you can see the detail you can get but you need to work at it.
This is an STL file and if you set up to turn your blank over to cut both sides you would have a 3d model in full, or cut two seperate sides and attach together.
http://www.mycncuk.com/attachment.ph...id=15490&stc=1
A bit busy but will try to help. Send file and desired size at costademaria @ gmail.com. send me as much info possible , material, why, what when....
Hi all, i am searching for a software which can convert multiply color images to depthmaps, so i can make a relief from a depthmap using Aspire. Any idea ?
if you want good result, forget about multiple. You will need to touch manually here and there. But Photoshop can do all you need, batches also. In fact Photoshop is the standard. All else is a copy of it. But check if Lightroom could do that.
No program in the world will do a real high quality 3D model/ bas relief from a photo.
It's an artistic work only a human can do.
Its art rather than science, how far in depth do want to go
http://www.cnc4free.org/
Cambam and Meshcam Art both have fre trials and will do bmp to height maps
Height map is a totally different thing.