Search:

Adhesive wise, I'd use a Polyurethane Adhesive Sealant, they are used to fix vehicle body panels and windscreens and are flexible enough to withstand a lot of abuse whilst providing a firm hold in an...

There may be guys that do Metal & Wood and CNC Lathe & CNC Milling but that's not very common in my experience of hobby & small professional machinists.
You might get a wider response to your RFQ...

Welcome Chris!
If you use toothed belt drive from your steppers to your ball screws you can get the movement speed you want with pulley ratios.
I don't have a gantry machine, but if I did I'd...

Rob,
Yes, the filament is rarely bang on size but the slicer assumes you gave it a precise diameter for volume calculation so I correct for variation in filament OD.
Bang on with "Spread" too ;-)

I measure filament.
My printer makes parts absolutely predictably 0.15 past the edge of the model, both internal and external, allowing me to compensate precisely and make on size parts.

https://www.aliexpress.com/item/1-Pcs-Wood-Stainless-Steel-Flat-Pressure-Roller-Leather-Blank-Holder-Device-Hand-Push-Roller-Hand/32750710444.html
...

For prototyping buy 1m to 3m lengths of tube with a slightly smaller hole than you think you need. Cut to length yourself with a hacksaw, holding the tube in a vice, use masking tape to mark the...

No, it's not.
Drive screws have a fast outer helix with a relatively high sharp profile, they are designed specifically for blind holes where the relative sizes can be chosen such that material...

To repeat myself because it's the quickest, simplest, cheapest and closest to requirements.
Tube axle (fully inside the bracket)
Holes in the bracket the same size as tube bore
Hammer Drive...

To do what? You don't have the area to securely bond the tube to the channel with epoxy so why would you want to put epoxy there?
Tube
Holes in the channel the same size as the tube ID.
Hammer...

You need to step away from your fixation on a fastener designed for easy use in non-engineering applications, they don't make threaded Chicago Screws without driver slots because they need to be user...

Anything with a high point that a proximity switch can sense at a repeatable point in the homing direction will do, you could use a single bladed chopper too, anything which sticks out significantly...

When people ask me about making one-offs for them I always tell them that if someone already sells it in this country, almost regardless of price, that's going to be cheaper. I even do a...

Join, read and follow the FaceBook Skyfire Owners Groups before making a decision.
Factory support and even communication seems to be less than it should be.

I've been very methodical and worked through all the steps required to properly commission the Syil X7, this week finally got around to cutting some chips.
This video shows a bit of the machining...

I don't work in Fusion but there should be an option to convert the font to line and curve geometry.

It's like the 1990s with apple updating Mac versions first :D

Brian,
I have seen quite a few reasonably priced used compact industrial CNC vertical machining centres.
What kept me from buying one was the proprietary nature of parts and systems incorporated...

I did think about making the 4th detachable but the hoist is simpler and relatively risk free.
You're most welcome to call in for a tour if you're ever passing.
These are some pics George shared...

Hmm, I kinda might, especially as it's permanently wired, I think I'd spot the ragged end of the cables! ;-)
The plan is to hang it from a hoist above the machine whilst machining arrays of parts...

One from the front

25522

Yours in the shop for repair too? ;-)

Good call Clive!
I rarely think of the basic machine set up being at fault! :D

If you make 6mm holes for switch access you can make neat little Top-Hat shaped buttons to fit from the inside of the case prior to fixing the pulse generator, it makes the job neat, the buttons easy...

From your link -

"The SPINx1 is a one channel isolated digital potentiometer intended for spindle control. The SPINx1 takes three TTL level signals, PWM, DIR and ENA and has four isolated...