DDSCV1.1 3 and 4 axis offline motion controller

[Joules]

Thanks, thats just the picture I needed.

[John S]

These controllers are going to be a game changer for the many people sat on the fence telling themselves CNC is too hard to get into.

[magicniner]

These look great, what Lathe/Mill Post Processor is required to generate code for them?

Most similar things I've seen claim "Standard G-Code" but then don't mention which easily available Post Processors produce "Standard G-Code" as all the PPs I've found have a manufacturer/machine/controller designation.

Mach3 developers had the good grace to work close to a standard for a popular industrial controller rather than a paper standard to which no manufacturer quite adheres.

These controllers are going to be a game changer for the many people sat on the fence telling themselves CNC is too hard to get into.

Never underestimate the incapability of the masses, there's still all those scary wires to connect ;-)

- Nick

[Boyan Silyavski]

These look great, what Lathe/Mill Post Processor is required to generate code for them?

Most similar things I've seen claim "Standard G-Code" but then don't mention which easily available Post Processors produce "Standard G-Code" as all the PPs I've found have a manufacturer/machine/controller designation.

Mach3 developers had the good grace to work close to a standard for a popular industrial controller rather than a paper standard to which no manufacturer quite adheres.



Never underestimate the incapability of the masses, there's still all those scary wires to connect ;-)

- Nick

That's the big question before jumping to conclusions

What i found till now:


- Post processor for mach3 definitely does not work, as you could see in second video it runs away from the job coordinates. Who cares, me not. I could save my programs again in the proper format


-It doe not recognise manual tool change code also. So jobs have to be split. Not big deal

-Does not recognise G20 and G21, so program must be in mm to begin with. No problem so far.

-Will run properly G code as of the Gcode and fanuc output from Aspire. Though program was simple. / See video2/ .


As i have not connected it yet to a machine i can not say more. But there is a good chance that all goes fine.

[magicniner]

-It doe not recognise manual tool change code also.

Does it support a Tool Changer/Turret etc. ?

[Boyan Silyavski]

This is a basic controller. The much more expensive Chinese controllers not only do all but close the loop also, at least the most expensive ones, which makes them really industrial

funny, i see now that it supports G20 and G21 but when i was testing it ?, so maybe i made a mistake somehow with the file. Will check again

That's what it supports.

[John S]

Does it support a Tool Changer/Turret etc. ?

No and neither does Mach 3 or LinuxCNC without 3rd party boards and a load of tossing about.

They are basically a cheap foray into CNC without a PC, monitor, licenses etc and all the Mumbo Jumbo that Mach and Linux entail.

[magicniner]

No and neither does Mach 3 or LinuxCNC without 3rd party boards and a load of tossing about.

They are basically a cheap foray into CNC without a PC, monitor, licenses etc and all the Mumbo Jumbo that Mach and Linux entail.

I'm just trying to get a feel for whether it's a direction in which I should move, it does look like a great first foray into CNC solution, but given that I'm already au-fait and comfortable with Mach's Mumbo Jumbo I was looking for a step up rather than a step sideways and possibly down.

Although I've yet to have a PC fail I have upgraded my controller machine a few times to the point where it will hapily run my CAD/CAM. One very nice feature with Mach3 is that for approximately £60 I am able to have a fully configured, 100% functional backup PC with a new HDD on the shelf and any keyboard or monitor from my other systems can replace the ones on the CNC in the event of failure.

With any luck these all-in-one boxes will take off in the starter CNC market and grow with their customer base to offer enhanced capabilities,

- Nick