DDSCV1.1 3 and 4 axis offline motion controller

[foto-boss]

In DDCSV2.1 change PNP inputs to NPN!

[Bubbles]

In DDCSV2.1 change PNP inputs to NPN!

Is there anyway to make the DDCSV2.1 work in inches rather than millimeters?

[magicniner]

Is there anyway to make the DDCSV2.1 work in inches rather than millimeters?

There might be but My CAM allows me to swap between measurement systems so I can POST code in inches even though I work in mm.

[bikepete]

A few links to save others searching maybe: DDCSV2.1 doesn't yet seem to come up with UK ebay searches (still just the 1.1 version) but some 2.1 details and manual downloads are here and a USA ebay listing is here.

[Bubbles]

There might be but My CAM allows me to swap between measurement systems so I can POST code in inches even though I work in mm.

I use CAMBAM. It lets me change between inches and mm.

I already have many files created in inches. Changing them to mm instead of inches seems to make no difference.

When I try to run one in inches it seems to run in mm instead of inches.

My spindle is calibrated to move 25.4mm to get 1in of travel, so assume if I increased my numbers 25.4 times I would get what I want. Except I don't want to go through my files and convert them manually.

Am I missing something to get files to run at a 1 on the display = 1in ???

Thanks for your responses so far guys!

[magicniner]

I use CAMBAM. It lets me change between inches and mm.

I already have many files created in inches. Changing them to mm instead of inches seems to make no difference.

When I try to run one in inches it seems to run in mm instead of inches.

My spindle is calibrated to move 25.4mm to get 1in of travel, so assume if I increased my numbers 25.4 times I would get what I want. Except I don't want to go through my files and convert them manually.

Am I missing something to get files to run at a 1 on the display = 1in ???

Thanks for your responses so far guys!

Does the code have a G20 in it?

[Bubbles]

Does the code have a G20 in it?

Here are the first few lines of one of the files.
( Made using CamBam - http://www.cambam.co.uk )
( chickenfoot 12/26/2017 9:42:57 AM )
( T0 : 0.0001 )
( T1 : 0.125 )
( T4 : 0.25 )
G20 G90 G64 G40
G0 Z0.125
( T4 : 0.25 )
T4 M6
( Profile1 )
G17
M3 S1000
G0 X-2.25 Y-0.375
G0 Z0.0625
G1 F200.0 Z-0.015
G1 F1000.0 X-3.0847
G3 X-3.2081 Y-0.52 I0.0 J-0.125
G3 X-2.6742 Y-1.8469 I3.2081 J0.52

[cropwell]

Am I missing something to get files to run at a 1 on the display = 1in ???

In the links in post #229 is a download for the English manual. On page 80 there is parameter #115 0=metric,1=imperial.

https://www.cnccookbook.com/g21-gcod...tric-imperial/

[Bubbles]

In the links in post #229 is a download for the English manual. On page 80 there is parameter #115 0=metric,1=imperial.

https://www.cnccookbook.com/g21-gcod...tric-imperial/

I don't find parameter #115 in my parameter page.

[Bubbles]

I don't find parameter #115 in my parameter page.

I have tried installing the latest firmware listed in that post but I don't have parameter 114 or 115 and possibly others.

I am guessing I am running an older version of the firm ware even though my disply says Ver: 2017-04-16-IM NOR