Newbie looking at 6040 (China CNC) for polypropylene 15mm sheet

[JOGARA]

Would something like one of this work?
http://www.airlinktransformers.com/c...Filter+Results

They have 70+70V so would mean 2 sets of 70V?
From what I know, you can connect these in parallel though you have to be careful to get the phases the correct way round?

As for the rating, thinking 2000VA?

As for caps, 110v and as big as i'd like?

[Clive S]

Would something like one of this work?
http://www.airlinktransformers.com/c...Filter+Results

They have 70+70V so would mean 2 sets of 70V?
From what I know, you can connect these in parallel though you have to be careful to get the phases the correct way round?

As for the rating, thinking 2000VA?

As for caps, 110v and as big as i'd like?

Ok what DC voltage to you want to end up with. What steppers are you using and how many.

Read #31 again 650VA should be more than enough try and get caps that are 100V

http://www.airlinktransformers.com/c...Filter+Results

[JOGARA]

Ok what DC voltage to you want to end up with. What steppers are you using and how many.

Read #31 again 650VA should be more than enough try and get caps that are 100V

http://www.airlinktransformers.com/c...Filter+Results

Going off what people said, higher voltage the better? So close to the max of the drivers.

As for the drivers, http://www.zappautomation.co.uk/elec...ion/em806.html (buying direct from manufacturer in China)
Steppers, http://www.zappautomation.co.uk/elec...ion/em806.html

[Neale]

Going off what people said, higher voltage the better? So close to the max of the drivers.

...which is what you will get if you use a lower voltage transformer. Yes, I know it doesn't sound right, but in practice a 45V or so transformer will end up giving you around 68V DC across the smoothing capacitor(s). This also gives a bit of allowance for the fact that the mains input voltage will vary, and the transformer will probably give you about 5% over the rated voltage under light load to allow for a drop when on full load.

EM806 are good drivers.

[Clive S]

Going off what people said, higher voltage the better? So close to the max of the drivers.

As for the drivers, http://www.zappautomation.co.uk/elec...ion/em806.html (buying direct from manufacturer in China)
Steppers, http://www.zappautomation.co.uk/elec...ion/em806.html

Those are 80V drives so run them at about 68V to allow for the back emf. 24-24 v in series = 48 = about 68V dc when rectified.

AM882 drives would be less dosh and just as good.

[Clive S]

Snap

[JOGARA]

Those are 80V drives so run them at about 68V to allow for the back emf. 24-24 v in series = 48 = about 68V dc when rectified.

AM882 drives would be less dosh and just as good.

Ohhh
I thought it was 1:1 from transform through rectification.
That makes sense why so many are doing 24-24v.

These are the drivers I am getting https://www.aliexpress.com/store/pro...615.0.0.9rnD8Q

Forgot I changed to them.


Am I right in saying that when the steppers start up or change direction, they require a lot of amps, but when they are going it is pretty low.
Which is why you are able to get away with lower wattage transformers?



Thanks

[Clive S]

Am I right in saying that when the steppers start up or change direction, they require a lot of amps, but when they are going it is pretty low.
Which is why you are able to get away with lower wattage transformers?

A 625 va trans former will be fine good choice on the AM882

[JOGARA]

Doing an order from TME already, saw they sold toroidals.
http://www.tme.eu/gb/details/tst600w...del/tst600008/

Though it is 600VA not 650VA.
That extra few watts going to make much difference?