Spindle stopping at 10,000 rpm?

[Boyan Silyavski]

Find a seller that sells it on aliexpress or ebay, contact him and ask him for the manual. That simple.

Where did you buy that spindle from?

Or download a typical Chinese spindle manual, al is same same, with small differences. Find there the max frequency and max it to 400hz.

here is the manual in Russian https://docviewer.yandex.com/?url=ya...c=58b415ee5c3b , lame but you can use copy past in google translator and get the important stuff


from there:
List of parameters 5.2 function
Function number Setting range Value Function Description Default Comments
P-000 Frequency setting mode selection
0. Control panel ▲, ▼ to set;
1. Panel Potentiometer
2. Potentiometer FV terminal or setting 0-10;
3. FI terminal installation of 4-20 mA signal;
4. Control Panel ▲, ▼ set, if it is detected from the terminal to the FV potentiometer or 0-10V
The signal will automatically switch to 5;
5. Potentiometer terminal FV or setting 0-10, if detected panel ▲, ▼ work
Automatic switching to 4;
4 √
P-001 Running command selection
0. Control panel (Forward rotation start, reverse start, stop);
1. Control Terminal (forward / stop and reverse / stop);
2. Control Terminal (start / stop, forward / backward);
3. Control Terminal (forward rotation start, reverse start, stop (NC));
4. Other methods that automatically adapt;
5. Control Terminal (forward rotation start, reverse start, stop (normally open));
4 ╳
P-002 Stop Mode
0 Deceleration stop;
1. Free stop;
2. DC brake immediately;
0 √
P-003 prohibits the reversal of the engine
0. This allows the engine to the contrary;
1. Disable the motor reversal;
0 √
P-004 keyboard to prohibit the reverse rotation start
0 Enable reverse keyboard start;
1. Prohibition of the keyboard reverse start;
1 √
P-005 Start frequency 0.0-highest operating frequency of 1.0 Hz √
P-006 Start delay 0.0-60.0 seconds to 0.0 seconds ╳
P-007 Reserved
P-008 automatic voltage sensitivity of 0 (lowest) to control 3 (high) 1 √
P-009 Slip compensation 0.0-5.0Hz 0.0Hz √
R-010 carrier frequency of 1000 Hz-12000Hz. When the carrier 999 by using a set of △ ╳
The frequency of P-011 achieves a set 0.0-2000.0Hz 0.0Hz √
Selection of P-012 analog output
0 Analog frequency;
1. Analog current device;
2. The analog voltmeter;
0 √
Twenty three
P-013 Analog Output Gain 50-200% 100 √
P-014 Power Selection Show
0. Frequency (H, F);
1. Output current (A);
2. The bus voltage (U);
3. Approximate mechanical speed (r) = output frequency * P-015;
4. PID set value (y);
5. Inside the converter heatsink temperature (C);
6. The output voltage (U);
7. The counter value (J);
8. Feedback PID (L);
0 √
R-015 speed factor 0.01-99.99 30.00 √
User preferences Password P-016
0. Do not set;
Others, password settings, change the settings you must enter the value in the P-140;
0
P-017 0 memory frequency. No memory; 1. Memory; 2. memory before starting frequency; 1 √
P-018 is the instantaneous power failure restart 0. Invalid; 1. Track your speed; 2. Restart; 0 √
P-019 just restarted after a crash 0-10 times 0 √
P-020, and then start waiting time of 0-60 seconds, 10 seconds √
P-021 braking initial voltage
220 Inverter: 350-400V 360V √
380 Inverter: 650-700V 660V √
P-022 anti-overvoltage during deceleration response point
220 Inverter: 350-450V 400V √
380 Inverter: 650-750V 700V √
P-023 anti-accelerate in response to the points 110-150% over the nominal current of the inverter 130 √
P-024 anti-overcurrent response at constant speed at 110-150% of the rated inverter current 150 √
P-025 drive rated current ◎ △
P-026 motor rated current 20-120% of the nominal drive current 100 √
P-027 motor rated voltage
Model 220: 50-450V 220 ╳
Model 380V: 50-450V 380V ╳
P-028 Rated motor frequency intermediate frequency of 50.0 Hz -2000.0Hz ╳
P-029 intermediate voltage Minimum voltage -99% when the intermediate voltage is equal to the minimum voltage using torque boost 0 ╳
P-030 intermediate frequency 1.0 Rated frequency 12.5 Hz ╳
P-031 low voltage 0- intermediate voltage using torque boost 0 ╳, when the intermediate voltage is equal to the minimum voltage
When P-032 0-30 torque increase (due to different types of aircraft), the intermediate voltage is less than or equal to a minimum effective voltage △ √
P-033 the maximum operating frequency of the lowest operating frequency -2000.0Hz 60.0Hz √
P-034 low operating frequency of 0.0 Hz is the maximum operating frequency of 0.0 Hz ╳
P-035
High frequency (PID maximum
Setpoint) corresponding analog
To come in
0-100% 96 √
P-036
Low frequency (PID minimum
Setpoint) corresponding analog
To come in
0-100% 2 √
P-037 Reserved
P-038 frequency upper limit frequency -2000.0Hz 60.0Hz ╳
P-039 0.0-frequency limit the upper limit frequency of 1.0 Hz √
Twenty four
P-040 braking time 0.0-25.0 seconds 0.0 seconds √
P-041 DC braking torque 0-30 (due to different aircraft types) △ √
P-042 brake starting frequency Hz 0.0 -25.0 3.0 Hz √
The regulator R-043 Rotary
0. prohibited keyboard operation jogging
1. Allow the keyboard turning operation
1 √
P-044 Rotary frequency low operating frequency - maximum operating frequency of 5.0 Hz √
P-045 Acceleration Jog 0.05-650.00 seconds △ √
P-046 cooks