Hybrid View
-
28-02-2017 #1
Not a bad price for a Super 7 - the only cheaper one (ex-college, looking good) is on auction, not B-O, I'd expect any S7 to go for rather more than a grand. For anyone in the market it would be worth a look under the superficial surface grime - could be a good fixer-upper. The sellers look like they do house clearances - might be worth an inspection and a cheeky offer ("tssssk, chuck too small, mate, no live centre, £650 and I'm cutting my own throat")
-
28-02-2017 #2
-
28-02-2017 #3
£1000 for a heap of rust. myfords are very overrated. I used one like many others at collage and tech back in the 70,s. and when I went into model engineering purchased a myford because that was the lathe I knew. had a go on a mates Colchester bantam and the myford was gone the same week. o and my super 7 was like new and I sold it for £780 3 years back, the bantam also like new with power slides was £550 and worth it and more, a total joy to use and parting off is now a thing of joy.
-
01-03-2017 #4
Looking at the prices of everything else on the site its all WELL over priced!
-
01-03-2017 #5
-
01-03-2017 #6
That Myford's nothing. Check out this £700 beauty:
That tin of Quality Street had a lucky escape...
-
01-03-2017 #7
The item may have some signs of cosmetic wear...
-
01-03-2017 #8
the prick even sprayed the drill bit for gods sake. it makes me mad when these sort of people try to wreak my hobby by passing on junk like this.
-
02-03-2017 #9
-
02-03-2017 #10
I watch the prices that they actually sell for because I have a vague interest in tracking sale prices
[STANDS UP TO ADDRESS THE MEETING] My name is Nick and I am a Myford Super 7-aholic [SITS DOWN AGAIN]
and without a gearbox they don't often make a grand unless (i) accompanied by substantial tooling and accessories or (ii) they have hardened ways or (iii) they are the long bed variant.
Consider also that if a lower offer is accepted by a seller eBay systems still show the final price as the Buy It Now Price :O
I'm not actually Joined at the Hip to my Super 7, it has simply always done what I need it to do, up until the point where I could no longer manage with it's puny through capacity, even with it being the long bed version.
At the point when I was shopping for something larger a converted head became available, with 30.5mm through capacity and roller bearings (limiting speed to around 8000rpm!). Given the alternative of shopping for a suitable replacement, getting it running right and tooling it up to match the Myford, whilst still running the Myford for everyday jobs, before finally swapping out & selling the Myford the choice was easy.
My observation is that with a roller bearing head all the issues with "rigidity" seem to have disappeared. This lead me to the conclusion that the primary issue is not rigidity but the break-down under excess pressure/inadequate speed in the hydro-dynamic front bearing on the standard S7 and that only once this is forced off-centre does the work "climb" into the tooling and apply excessive force to the tool, holder, tool post, slides and ways.
Apologies for going off at a Tangent ;-)
- NickLast edited by magicniner; 02-03-2017 at 10:51 AM.
You think that's too expensive? You're not a Model Engineer are you? :D
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
NEW MEMBER: New member alert !
By Metal pecker in forum New Member IntroductionsReplies: 5Last Post: 16-01-2014, 04:41 PM -
Small lathe AC/DC motors on eBay
By cristec in forum Marketplace DiscussionReplies: 0Last Post: 18-11-2012, 06:59 PM -
Hello - Kerry lathe from ebay
By Bossco101 in forum Milling Machines, Builds & ConversionsReplies: 17Last Post: 05-12-2010, 10:48 AM -
FOR SALE: My old Southbend 415 9" lathe is now on ebay
By BillTodd in forum Items For SaleReplies: 0Last Post: 04-09-2009, 09:25 PM -
Noob alert - 'Starter for 10' feed rates for MDF
By HankMcSpank in forum Machine DiscussionReplies: 6Last Post: 04-06-2009, 01:06 PM
Bookmarks