Thread: Water table build.....
Hybrid View
-
04-04-2017 #1
Last edited by Skiprat; 04-04-2017 at 09:35 PM.
-
04-04-2017 #2
Measured the table to suit my table and got the plasma out and cut it into approximately half and the biggest bit was used to include a lip to be bent.
The left over piece is just a nice size for me to build the under table down draft system once the water table is sorted.
I cut the table in the back garden on the stones but dont tell the missus......i dont think she will see the mark left....
-
04-04-2017 #3
The hardest bit is bending the bugger into shape.....too big for my home made bender so i had to resort to neanderthal methods.....
Out came the hammers, clamps and earmuffs....
two hours later and this is how far i have got...but i will be back in there tomorrow hopefully..
Going to get my masons chisel and hopefully tighten the bend and possibly it needs shrinking where i have hammered it too much and caused ripples.
A bit of TIG and hopefully a nice new(ish) water table......will post updates as i go along.
-
05-04-2017 #4
Good work mate, glad you had a use for it
Sent from my iPhone using Tapatalk Pro
-
08-04-2017 #5
Got the table bent and welded together......not too keen on my welds as its the first time i have done stainless TIG.
Had a few test goes then straight into deep end........Should of had a few days practising but hey that,s me..
Welded the steel square ready for the straight pieces and lats but leaving that until another day....hopefully tomorrow.
Tried welding the holes in but that was a bit sh111tty too say the least so i will leave that bit until i have had a few more practises plus i need to watch a few videos as the settings i used were just the basic ones out of the manual and they kept burning through as seen in photo.
-
08-04-2017 #6
Well just been doing some research and when i think about it , the holes where already there and being used so why don't i just Blind PoP rivet them.....
Any thoughts on this please?
Cheers Tommy
-
14-04-2017 #7
-
07-05-2017 #8
Water table finished (done a while back but been busy on other bits, hence the late update). All riveted up and new slots cut. Only thing is i didn't get enough cut but don't think i will buy more unless i need them.
I'm not into business so probably only buy more if i need to cut a full sheet (unlikely at present.).Hopefully might make a few bob with one offs. Placed the original wood base for routing on top and you can also see the small "water table" which is what i do most of my cutting on.
Many thanks to all that helped. Just bought an air scribe so that's my next project.
Cheers Tommy.Last edited by Skiprat; 07-05-2017 at 11:27 AM.
-
07-05-2017 #9
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Stainless water table - FREE
By D-man in forum Items For SaleReplies: 11Last Post: 31-03-2017, 05:48 PM -
BUILD LOG: Table top cnc build
By kah in forum DIY Router Build LogsReplies: 0Last Post: 28-02-2016, 07:07 PM -
Second CNC table build, here we go again....
By Davek0974 in forum Plasma Table MachinesReplies: 118Last Post: 17-09-2015, 06:40 PM -
BUILD LOG: Let The Fun Begain, New build on the Table.
By Bush Flyer in forum DIY Router Build LogsReplies: 63Last Post: 20-11-2013, 09:19 PM -
3M x 2M Plasma table build
By MonoNeuron in forum DIY Plasma Build LogsReplies: 14Last Post: 01-09-2009, 11:11 AM
Bookmarks