Thread: Help with spindle please
-
04-09-2017 #1
I Have a Isel CPM 2018 thati have converted to run with Mach3 on it is a Isel UFM 500 ut it dose not have any collets oe a clamp nut, I have bought 2 different nuts and a set of ER11 collets, none of which fit the collets are the wrong taper and the nuts one size is too small and the thread on the other seems wrong like one is a taper they are CNBTR 11 A and other is CNBTR 11 M
dose any one have any Idea what collets and nut fit this spindle are they Kress? or do i just buy a chineese air cooled brushless??? or maybe a new Kress 800 or 1050 about same money
Thanks for any help
Steve
Last edited by Steve-m; 04-09-2017 at 10:51 PM.
-
04-09-2017 #2
Not got Google
https://www.isel.com/en/downloads/dl...h_englisch.pdf
?You think that's too expensive? You're not a Model Engineer are you? :D
-
04-09-2017 #3
-
04-09-2017 #4
They are proprietary, not an industry-wide standard like ER collets, that is where to buy them from, along with part numbers.
You think that's too expensive? You're not a Model Engineer are you? :D
-
05-09-2017 #5
thanks Got a price for a 3.175mm - 1/8" collet from them today £45 + £5 postage for each size, think a chineese ER11 spindle is the way to go. was hoping that someone may know if there Kress there a lot cheaper, google dose not know before some smart arse chimes in with google is your friend
Steve
-
05-09-2017 #6
..
Last edited by magicniner; 05-09-2017 at 06:41 PM.
You think that's too expensive? You're not a Model Engineer are you? :D
-
05-09-2017 #7
Thanks
Last edited by Steve-m; 05-09-2017 at 06:50 PM.
-
05-09-2017 #8
-
05-09-2017 #9
It actually looks like they aren't, the part numbers for the 500 and 1050 collets are different and Kress listing suggests they share a fitting with the 1050, not the 500.
You think that's too expensive? You're not a Model Engineer are you? :D
-
05-09-2017 #10
cheers I have found some kress 580 in germany may just buy one and see, But thank you for trying, I have spent weeks looking for collets and a nut, think im going to put in bottom draw and look into chinese spindle, start reading from scratch again
Steve
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Chinese 300W DC spindle - is the spindle shaft grounded?
By HankMcSpank in forum Spindles & Drive MotorsReplies: 44Last Post: 26-11-2016, 07:25 PM -
TB6560 controller Runs spindle on power up When Mach3 plunges spindle stops
By RoyT in forum Spindles & Drive MotorsReplies: 5Last Post: 29-09-2014, 02:42 PM -
CNC Spindle Repair and Spindle Replacement for any Machine of any Manufacturer
By spindeldoctor in forum Manufacturer NewsReplies: 0Last Post: 13-11-2013, 07:50 PM -
Spindle lock mechanism for 2.2kW china spindle
By Jonathan in forum Generic Chinese SpindlesReplies: 8Last Post: 13-08-2012, 08:39 PM -
DIY Spindle - What type of bearings are best suited for a spindle.
By 8iggles in forum Spindles & Drive MotorsReplies: 18Last Post: 09-02-2011, 10:15 PM
Bookmarks