-
07-05-2019 #61
As Clive says - a bit of overkill. In theory it should work, and the argument that the UC300ETH (or whatever) will only draw the current that it requires is correct, however, big PSUs like this are sometimes less well regulated when substantially under utilised. Chances are that it will work, but something closer to the requirement of the UC300ETH (and any BOB, limit switch, relays, etc) would be sensible. 2A would be my target for something like this.
-
15-05-2019 #62
Thanks for the link and the feedback, it's helping a lot in this project. Now I've got a few phone power supplies too, but the one problem is that the one is out putting 5.1 volts rather than the " exact 5 volt maximum." Is that something that should worry me? I know it's sounding a bit picky But it never hurts to ask just in case.
Thanks again in advance!
Sent from my Moto G (5) using Tapatalk
-
15-05-2019 #63
the extra 0.1V from your 5.1V power supply is not a problem
for 5V logic like the old 74series TTL logic
the limits for nominal 5V supply voltage is between the 4.75 min and 5.25V max
for 5V Atmel 8 bit micro controllers like the ATmega8 operating voltage is 4.5V to 5.5V
John
PS
any one know which micro controller has been used for the UC300ETH ?Last edited by john swift; 15-05-2019 at 12:18 PM. Reason: add PS - which micro controller
-
15-05-2019 #64
As John says, that voltage sounds fine. It could even be your multimeter that's slightly out.
I would guess the UC300 is using some form of ARM chip, regardless I'd guess whatever chip will be running at 3.3V. Even a few years ago, the vast majority of microcontrollers were running at 3.3V max, with 5V capable ones being a dying breed.Avoiding the rubbish customer service from AluminiumWarehouse since July '13.
-
15-05-2019 #65
m_c
your correct the micro controller is a 3.3V device
looking at a photo of the UC300 it has a
MICROCHIP dsPIC33EP256
from the MICROCHIP web site
Operating Voltage Range (V)
3 to 3.6
the dsPIC33EP256 Input/Output
• Sink/Source 10 mA on All Pins
• 5V Tolerant Pins
• Selectable Open-Drain, Pull-ups and Pull-Downs
• Up to 5 mA Overvoltage Clamp Current
• External Interrupts on All I/O pins
the UC300 board has a 5V supply connector
so the surface mount device between the 5V supply and PIC
must be a low drop out 3.3V regulator
John
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
CSLAB CSMIO/IP-M 4-axis Ethernet Motion Controller
By dudz in forum CS-Lab (CSMIO)Replies: 35Last Post: 02-01-2017, 01:27 AM -
BoB Suggestions within UK
By andy_con in forum General ElectronicsReplies: 9Last Post: 09-05-2016, 10:39 PM -
USB/Ethernet controller for Mach3/4 advice
By paulus.v in forum Control Hardware & SystemsReplies: 17Last Post: 17-02-2015, 09:37 PM -
Boring Bar Suggestions?
By Washout in forum Lathes, Lathe Rebuilding & ConversionsReplies: 10Last Post: 21-06-2014, 08:59 AM -
USB and Ethernet Mach3 motion controller PLCM-E3
By Purelogic R&D in forum Manufacturer NewsReplies: 39Last Post: 29-12-2012, 09:38 AM
Bookmarks