-
25-05-2018 #1
Hello together,
I would like to introduce you to my new project.
I call it "Solar Sphere".
It's an almost wearfree rotating sphere.
Because of magnets on the shaft and the substructure, it is able to float.
1 Hour of sunlight is enough to rotate the sphere for 2,5 days.
It took me 3 month to plan and build this construction.
So i would be glad, if you watch my video and tell me your opinion.
Have fun
Wolfram
-
The Following User Says Thank You to wolfram-g For This Useful Post:
-
26-05-2018 #2
Looks pretty, but why bring up "perpetual motion" in the video?
I know you said it is not perpetual motion but "is close".
That is like saying a solar cell and a small DC motor hocked to a small battery is "close" to perpetual motion xD
Not bashing but just seams odd?Last edited by JOGARA; 26-05-2018 at 01:28 AM.
-
The Following User Says Thank You to JOGARA For This Useful Post:
-
27-05-2018 #3
Nice project reminds me of a flywheel on magnetic bearings in a vacuum.
http://www.mycncuk.com/threads/10880...60cm-work-area My first CNC build WIP 120cm*80cm
If you didn't buy it from China the company you bought it from did ;)
-
28-05-2018 #4
Perpetual Motion is a What?
"On our planet we can only try to get as close as possible to this phenomenon"
Perpetual Motion is not a Phenomenon, in this reality, with the Prevailing laws of Physics, Perpetual Motion is a total fantasy and the preserve of the uneducated, cod-scientist and utter nut-job.
HTH,
:DYou think that's too expensive? You're not a Model Engineer are you? :D
-
The Following User Says Thank You to magicniner For This Useful Post:
-
10-06-2018 #5
Dear CNC friends,
rom my experiences of the last years, I have now built the final version of the SolarSphere.
SolarSphere 4.0
The advantages over the Model 3.0 are:
The drive (including lighting and loading module) as well as the substructure and the sphere are independent modules.
The sphere is made of polycarbonate and therefore insensitive to external influences.
The new rotor design eliminates the need for balancing.
The lighting is variable (the LEDs are plugged in and can be replaced by other coloured ones at any time).
Electricity consumption has been reduced by 80%.
The charging module (including USB connection) shows the operating status of the Lipo battery visually.
The magnetic bearing is stabilized and makes the rotor insensitive to vibrations.
These changes significantly reduce costs and production time.
SolarSphere 4.0: W=212mm D=148mm H=176mm
How it works is explained in the video down below.
Thanks for your interest
Wolfram
-
10-06-2018 #6
YouTube SPAM then!
I stopped watching and disliked your video when you alluded to Perpetual Motion being "Something we can't achieve here", it's something no one can achieve anywhere in our reality because it's utter bollocks!You think that's too expensive? You're not a Model Engineer are you? :D
-
11-06-2018 #7
Thanks Wolfram,
I like what you have shown here, and imagine you will market it as a kind of "Executive Toy"?
Andy
-
11-08-2018 #8
Dear CNC Community,
After talking about this topic long enough,
I finished the project „SolarSphere“ with the following video.
Thank you very much for your interest and patience.
And now enjoy my very last video about the
ever-rotating „SolarSphere 4.0“
Sincerely
Wolfram GlattharLast edited by wolfram-g; 11-08-2018 at 09:19 AM.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
1 voltage meter for both solar panel and battery
By deannos in forum General DiscussionReplies: 7Last Post: 01-08-2014, 07:41 PM -
Steam Engine made of GLASS
By WandrinAndy in forum General DiscussionReplies: 2Last Post: 13-06-2013, 09:57 AM -
solar tracking
By luke11cnc in forum Electronic Project BuildingReplies: 2Last Post: 27-04-2013, 09:47 AM -
NEW MEMBER: model engine builder in somerset
By Peter Griffin in forum New Member IntroductionsReplies: 7Last Post: 21-10-2012, 04:41 PM
Bookmarks