choosing a bleed resistor

[Doddy]

Nope, it's 220-240 on the primary of the toroidal, something that should be borne in mind for our US readers.

It uses a potential divider across the C1 capacitor and the relay coil. It works as-is, but is fraught with problems when people start substituting components.

[cropwell]

Sorry Doddy, I was trying to delete my post as I realised it was mains input. Just had a senior moment !

[the great waldo]

Nope, it's 220-240 on the primary of the toroidal, something that should be borne in mind for our US readers.

It uses a potential divider across the C1 capacitor and the relay coil. It works as-is, but is fraught with problems when people start substituting components.

Hi Doddy
I'm using a 500va 2x18volt toroidial transformer with 3 or 4 4700uf 100 v caps. 35 amp rectifier in my power supply, would the elektor circuit be ok with that power supply ? or should I hunt around for another soft start circuit ? Thanks in advance.
cheers

Andrew

[Clive S]

Hi Doddy
I'm using a 500va 2x18volt toroidial transformer with 3 or 4 4700uf 100 v caps. 35 amp rectifier in my power supply, would the elektor circuit be ok with that power supply ? or should I hunt around for another soft start circuit ? Thanks in advance.
cheers

Andrew

Personally I don't think you need one. I have a 625vA one that runs without any trouble and 3 caps is ample.

[the great waldo]

Hi Clive
I'll put one I found on ebay https://www.ebay.de/itm/131927219743 in just not to strain my wiring. It's an old house in the country here in Austria with a new distribution box wired up about 15 years ago which happens to be in the workshop as well so cable runs are not too long. A little peace of mind is worth the added expense for me.
Cheers

Andrew

[driftspin]

Personally I don't think you need one. I have a 625vA one that runs without any trouble and 3 caps is ample.

Hi Clive S,

You helped me with the parts list for the diy psu i have.

500va 2x25v.


No problems here either on 16amp B type CB.


Andrew, do you have issues on the mains power side?



In rush limiting is ok but not really needed when mains side is no problem.




Grtz Bert.



Verstuurd vanaf mijn SM-A320FL met Tapatalk

[the great waldo]

Hi Bert
I haven't put the supply together yet but it's an old house and I don't want to overload the the circuit breakers so it's really just for a bit of added protection.

Cheers

Andrew

[A_Camera]

Hi Doddy
I'm using a 500va 2x18volt toroidial transformer with 3 or 4 4700uf 100 v caps. 35 amp rectifier in my power supply, would the elektor circuit be ok with that power supply ? or should I hunt around for another soft start circuit ? Thanks in advance.
cheers

Andrew

If I were you I'd buy the one from Conrad, or something similar ready made. In my opinion it is not worth the effort and is safer and guaranteed to work. The reason I linked to that circuit is because you asked for an example. Anyway, if you decide to build it then in your case I think it needs some modification, so I'd modify the following:

1. The four resistors, as Doddy mentioned already. It is better to use more powerful type, even if the 5W may work for such application because of the short time current if flowing trough. In fact, I think a single resistor would be better, something like this:

https://www.conrad.at/de/ate-electro...st-420251.html

That one is 47 Ohm, so the current will be limited a little more, to 4.9A Instead of 5.75A with the 40 Ohm, but that doesn't matter.

2. The relay in the example is 8A, I'd take a more powerful one, for example this one:

https://www.conrad.at/de/printrelais...st-502934.html

3. The fuse should be 10A slow type.

4. The art work in my opinion should have more powerful tracks, especially on the K1, K1 and the relay part. No need to waste copper by removing more than what's necessary to provide isolation.

5. Resistors R1, R2 and R3 should be metal film, 0.6W or 1W type. Even if the current trough is low, it is good practice to use better resistors than coal film type.

https://www.conrad.at/de/metallschic...t-1417688.html

https://www.conrad.at/de/metallschic...t-1417626.html