. .
Page 4 of 6 FirstFirst ... 23456 LastLast

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Quote Originally Posted by cropwell View Post
    You may wish to revise the end-on approach, the first time you jog into and crush a switch. Don't ask me how I know. They work just as well when the profile just glides in from the side.



    Rob-T
    + one
    ..Clive
    The more you know, The better you know, How little you know

  2. The Following User Says Thank You to Clive S For This Useful Post:


  3. #2
    Hmm, I could mount it sideways on. Im planning on using it as one of the home switches and just using mechanical switches for the limits that I would mount on the other side.

  4. #3
    Cropwell I've just been playing with the homing function and guess what? I did manage to run into the proximity switch. No damage though because I had my cursor on the reset button in Mach 3 and the switch mount wasn't fastened down. What I can't understand is why is the proximity switch detecting the gantry, stopping and backing off as it should but then moving forward crashing into the proximity switch. Could it be because I haven't set my steps per mm properly yet?

  5. #4
    Long time since I've used Mach 3, but likely you have the direction of the final homing move or the position of the switch (in software) set wrong.

    Mach 3 thinks it needs to do a final move in that direction.

    I could solve it if you were using LinuxCNC.

  6. #5
    Jogging seems to ignore home switches.

  7. #6
    Quote Originally Posted by cropwell View Post
    Jogging seems to ignore home switches.
    Time to set up the soft limits before bolting that end-stop in place.
    An optimist says the glass is half full, a pessimist says the glass is half empty, an engineer says you're using the wrong sized glass.

  8. The Following User Says Thank You to Kitwn For This Useful Post:


  9. #7
    Ive changed homing settings in Mach and it woks fine now. Other problem was the steppers were stalling but I've increased the current output on the drivers and its flying along now.
    Just need to learn how to work out steps per mm with my 2005 ball screws and 26 teeth driver pulley to 22 teeth driven ratio.

  10. #8
    Quote Originally Posted by chillybo View Post
    Ive changed homing settings in Mach and it woks fine now. Other problem was the steppers were stalling but I've increased the current output on the drivers and its flying along now.
    Just need to learn how to work out steps per mm with my 2005 ball screws and 26 teeth driver pulley to 22 teeth driven ratio.
    Don't fry your noodle trying to work it out just let mach3 do it.! . . Go to the Settings tab, just above Reset there's a button says "Set Steps per unit" this will work it out for you by moving a distance you tell it and by measuring the actual distance it moved it works out the Steps per required.

  11. The Following User Says Thank You to JAZZCNC For This Useful Post:


  12. #9

  13. #10
    Thanks for that information Jazz. My noodle is easily fried. I used a digital calliper and let the gantry push it up against a stop on the rail. Ive unwired it all now because my control enclosure was delivered today. Im going to use the proximity sensors for homing and mechanical switches for limits. I'l position the limit switch so the gantry just touches it without switching when its detected by the proximity sensor. That way if the gantry goes to close the sensor it'l trip the limit before it damages anything.

    https://www.youtube.com/watch?v=HZF8jKtbkvo

Page 4 of 6 FirstFirst ... 23456 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Proximity wiring for limit switches, safety relay and a contactor
    By CharlieRam in forum General Electronics
    Replies: 15
    Last Post: 02-06-2019, 11:18 PM
  2. EMC2 home/limit switches... only acting as limit?
    By vputz in forum LinuxCNC (EMC)
    Replies: 4
    Last Post: 15-10-2014, 09:51 AM
  3. Help needed with proximity switches
    By Boyan Silyavski in forum General Electronics
    Replies: 6
    Last Post: 11-07-2014, 03:29 AM
  4. Proximity Switches
    By kingcreaky in forum General Electronics
    Replies: 20
    Last Post: 23-10-2013, 01:30 PM
  5. Proximity Sensors as Limit Switches ?
    By Lee Roberts in forum General Electronics
    Replies: 5
    Last Post: 03-10-2009, 07:04 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •