Joe90's BIG RAT Build.

[AndyUK]

Wow that's some serious brewing activity...

Don't worry about phases in your calculation. Just take that single phase value, 4A or so and go with it.

If your Calcs end up needing more than 1000kVA you're probably not quite right, or you're building a beast. Most builds here use around abouts 500kVA.

I won't comment on the information you've already seen from my build log - no point hearing the same persons opinion twice. Although I will add that I think I was a little conservative with my secondary voltages in retrospect, and could have gone higher.

[Clive S]

Wow that's some serious brewing activity...

Don't worry about phases in your calculation. Just take that single phase value, 4A or so and go with it.

If your Calcs end up needing more than 1000kVA you're probably not quite right, or you're building a beast. Most builds here use around abouts 500kVA.

I won't comment on the information you've already seen from my build log - no point hearing the same persons opinion twice. Although I will add that I think I was a little conservative with my secondary voltages in retrospect, and could have gone higher.

That would be some big machine

[joe.ninety]

That would be some big machine

Yes, I think there's been a of 'k' inserted where it shouldn't be. Lol

Can you imagine the size of the donut for a 1000kVA toroidal... Probably about the size of a truck tyre inner tube blown up to its max.

[AndyUK]

That would be some big machine

Yes, 1000kVA would be about 750 hp. You'd need your own substation to be installed. Even 500kVA / 380hp would be pushing it. You can safely drop the k....

Yes, I think there's been a couple of 'k's inserted where they shouldn't be. Lol

Ooops. :)

Force of habit I'm afraid... work requires kV / MV... You know what I meant!!

[Neale]

It's easy to get too wound up about these things. Whether you should use 60%, 70%, or 80% really doesn't make a bit of difference - if you are using a linear (i.e. toroidal transformer, etc) anyway, in practice, the average load will be way lower. Doesn't matter to the transformer - as long as it's rated for the average load with a bit left over, its thermal mass is so great that a few seconds a bit over rated current won't worry it. The rectifier is coping with short high-current pulses anyway as it charges the capacitors towards the peaks of the cycle. And capacitors aren't that critical as regards value as this is a CNC machine, not an audio amplifier. Ripple is not an issue. My drivers, for example, are rated for something like 20-80V input. A few volts more or less ripple ain't going to bother them any. I use a 650VA transformer that gives me around 67V and it doesn't even get warm.

Different case if you are using a switched-mode, stabilised, power supply. They are much less tolerant of peak loads and you might be safer over-specifying if you use one of those. Which is why linear PSUs are generally recommended!

[JAZZCNC]

As the others say don't get stressed over it and just build to give the required amps plus a few spare. Work on 60% of the total Motors rated amps and it will be fine.

Don't go crazy OTT with the amps because you will end up with a large Va rating and the inrush will bite you. 500Va does most 3 axis machines and 625Va for 4 axis running typical 4.2a steppers with 60-70Vdc. These are tried and tested values on 100's of machines.

[Muzzer]

Yes, 1000kVA would be about 750 hp. You'd need your own substation to be installed. Even 500kVA / 380hp would be pushing it. You can safely drop the k....

[Doddy]

I think you're all missing the important part of this thread. How's the beer? (if you don't mind I might PM you over this - I've a similar interest, or at least an interest in getting the missus interested).

[joe.ninety]

I think you're all missing the important part of this thread. How's the beer? (if you don't mind I might PM you over this - I've a similar interest, or at least an interest in getting the missus interested).

Well it would probably be a case of the blind leading the blind, as I've never attempted an all-grain brew before. To be honest, it's typical of me to go out and splurge instead of dipping my toe in slowly. Some people start with large pot/pans and commercial tea kettles/boilers but that would have meant too much time in the kitchen and under SWMBO's feet.
I only made the plunge last week and it hasn't even been delivered yet. It'll have a decent sell on value so it I decide it's not for me then I'll just stick it on fleabay.

I've done plenty of home brew but only from kits, nothing where I've made the wort from scratch. In fact a good deal of enthusiasts don't even consider that home brewing, I guess it's the male equivalent of making a sponge cake from a mix rather than individual ingredients.

Getting the missus interested is a bit of a double edged sword... It helps with approval for financial outlay, but I've now found mine drinks too much of the stuff I make and I've had to take to hiding it

Anyway, give it a couple of months and I'll probably be in the position to offer some advice. In the mean time check out this guys channel on YouTube...

https://www.youtube.com/channel/UCb3...aVDeulH1mZGW1Q

One of the best I've found, an English guy living in Denmark who works in the industry. Really informative without all the added guff... Not like a lot of the US brewing channels you find.

Cheers

[Kitwn]

I'm with you Doddy! There's a definite new social possibility in this thread... "come round for a free beer and have a look at my home-made CNC machine". I might be abe to make some friends!

It is something of a minefield trying to understand what the ratings of various components mean and how they need to be interpreted when designing a machine from scratch. Best thing is to just do what Dean says, as usual!

Kit