NordicCNC's build log

[JAZZCNC]

I've seen that atleast both DMM and Sunfar recommends either mains filter or both mains filter and line reactor for the mains power supply. I have seen people here using line filters but I haven't come across anyone using line reactors yet. Is that really as necessary as the manufacturers are claiming it to be?

Also mounting the electrical enclosure directly to the frame (made of aluminium) would it be a problem since it would basically be in direct contact with the machine frame? I mean that would be a direct earth connection for the enclosure. I am not too into electronics (yet)!

I would at least fit a mains filter because of them being Servo's, however, I have seen that some people have had issues with DMM servo's because they didn't use line reactors so you might want to fit them to be safe, or just go with mains filter and if you get any issues you can always slip a line reactor in between.!
It mostly depends on your incoming supply quality I think and I seem to remember those who have had issues where US based which works on different Freq and voltage to EU.

Regards the frame then yes it's fine and you would want the earth to the frame anyway for safety just in case a wire shorted to the frame.

[NordicCnc]

I would at least fit a mains filter because of them being Servo's, however, I have seen that some people have had issues with DMM servo's because they didn't use line reactors so you might want to fit them to be safe, or just go with mains filter and if you get any issues you can always slip a line reactor in between.!
It mostly depends on your incoming supply quality I think and I seem to remember those who have had issues where US based which works on different Freq and voltage to EU.

Regards the frame then yes it's fine and you would want the earth to the frame anyway for safety just in case a wire shorted to the frame.

No. That will be fine just make sure that all grounds go to one star point. If the frame is painted I would make a direct connection from the box to the frame.

Thanks both of you! This helps a ton. A line reactor costs about 100€, so not a big deal. I will fit one just to be sure!

Skickat från min SM-A530F via Tapatalk

[NordicCnc]

JAZZCNC, if you read this I have a question for you. How do you go about assembling the L-shape gantry together? I have received my aluminium profiles and to my surprise I noticed that they are not flat in the middle. It is probably hard to see in the picture but it is about 0.5mm.



I was thinking that I could sand it down, since the only critical thing would be that it is flat on the sides so that it wont wiggle when assembled.

[JAZZCNC]

JAZZCNC, if you read this I have a question for you. How do you go about assembling the L-shape gantry together? I have received my aluminium profiles and to my surprise I noticed that they are not flat in the middle. It is probably hard to see in the picture but it is about 0.5mm.

I was thinking that I could sand it down, since the only critical thing would be that it is flat on the sides so that it wont wiggle when assembled.

I've never seen profile made like that.? If that picture is showing it correctly it looks like a flattened pyramid.!! . . . The profile I use is always flat but if there are any slight highs or lows I just shim the rail to suit.

[NordicCnc]

I've never seen profile made like that.? If that picture is showing it correctly it looks like a flattened pyramid.!! . . . The profile I use is always flat but if there are any slight highs or lows I just shim the rail to suit.

Yes exactly. I got them from a local supplier, since I was not able to find any 160x80 heavy version profiles anywhere. Only the local supplier could offer them.

Ill probably face them in my crappy cnc router. It will be flat enough that way. I can probably get within 0.2mm over the 1200mm lenght. I wll then just shim the top raik.

Skickat från min SM-A530F via Tapatalk