Thread: Beavermill conversion to CNC
-
21-11-2009 #11
Hello everyone,
Today I did the scraping of the X axis.
I've needed the whole day for it and tomorrow I will also have a few hours
to do before it is ready.
-
23-11-2009 #12
I'm still not done scraping on the X axis it takes more time than I thought
anyway I continue until everything is straight.
This week I am planning to order the servo's This week from Zapp automation
I think the set servo motors from 1000 watt hopefully they are strong enough
-
23-11-2009 #13
It's looking good Andre,
I've never owned a machine with hand-scraped surfaces - will do soon though I hope. Just out of interest, the X axis bearing surfaces look quite long (it looks maybe 1500mm?). What are you using as a flatness reference to scrape this surface?
-
23-11-2009 #14
Hi Tom,
It is 1400 mm long and I have a special tool that I can use .
I will tomorrow make a picture and show you.
-
25-11-2009 #15
Tom ,
This is the tool that I talk about .
There are many shapes and designs available.
Or if you are in possession of a flat table, you can make one yourself.
Are you planning to scrape your own machine?
I can only say one thing "patience"
-
26-11-2009 #16
Hi Andre,
Thanks for the pics. Actually I was just curious about how to stabilise the flatness over such a long and thin shape. Of course a triangular section is obvious to me now! :)
My machines do not yet deserve scraping. In the UK we have a phrase "making a silk purse out of a sow's ear". It means that I could try for a long time with lots of sewing to turn a cow's ear into a silk purse. In the end, maybe it would look a bit like a silk purse. But actually it would always be a sow's ear!
It's the same with my cheap lathe! :) I'll save the scraping for another lathe...
I had thought about making a small flatness reference by scraping 3 plates into each other - but that would take a long time too!
-
02-12-2009 #17
I have spent the last days designing the axial bearings
and have done research for which
configuration I am going to use.
I had first thought of using a ZARN type of bearing .
But they were too expensive .
So I made my own a design with two axial needle bearings and one radial needle bearing.
Then I have the same result as the ZARN bearing.
I can preload them as I want.
Today I received the CNC handwheel.
-
15-12-2009 #18
Hello everyone,
We finally have finished scraping bearing surfaces on the X axis.
I decided to start from the basics because I had discovered that the table
was bend at the ends about 0.4mm on both sides.
I will show pictures of what I did to get it right.
Maybe something that someone can use it for his own project.
The first thing I did was to facemilling the carrier.
Then I milled the pigeons tail .
Then I finished it on the granite block with the scraper.
So this is straigth.
I will show you the tools aswell.
1 small scraper and 2 larger tools.
-
15-12-2009 #19
Then I focused my attention on the table and have them placed on the milling table with a hoist because it weigh about 150kg and that is a bit heavy to manually manipulate.But first I have them measured and marked points with the correct height and recorded them on the piece.
I then aligned them both height and direction .
Next I face milled both sides and the top because the top surface was not straight olso.
After aligning the table under the correct angle with a 3d measurment device I milled the pigion tail .
Later I scraped the surfaces again .
The end result is a maximum of 20 microns difference over the full distance 1420 mm
both the flat faces and the pigion taile.
For checking the flatness I used a clock and a triangle block for scraping and for the pigion taile a micrometer and 2 cilinders .
And I use for scraping the Prussian bleu oilpaint to see what I did
otherwise you will not know where to remove matarial.Last edited by Andre; 15-12-2009 at 07:43 PM.
-
15-12-2009 #20
this is the triangle schape
Thread Information
Users Browsing this Thread
There are currently 2 users browsing this thread. (0 members and 2 guests)
Similar Threads
-
CONVERSION: Archdale Conversion
By meyerga00 in forum Conversion Build LogsReplies: 0Last Post: 17-06-2012, 09:24 AM -
Mill conversion to cnc
By wolsey in forum General DiscussionReplies: 1Last Post: 15-08-2011, 11:07 PM -
Bridgeport Conversion
By Tony Goodwin in forum Bridgeport Milling MachinesReplies: 0Last Post: 08-08-2011, 08:11 AM -
Sieg sx2 conversion kit
By Goldigger in forum Milling Machines, Builds & ConversionsReplies: 3Last Post: 24-04-2011, 07:42 PM -
A little conversion tool
By D-man in forum Computer SoftwareReplies: 1Last Post: 18-12-2010, 04:58 PM
Bookmarks