Hybrid View
-
12-12-2020 #1
Hi, can anyone help me out with the setting for the VFD YL620-A2.2KW 220V and 2.2KW water cooled spindle?
I bought my spindle and VFD 5 years ago and never used them, however I've now fitted them on a CNC router and the VFD failed so trying to add the VFD YL620-A2.2KW 220V (Amazon) but don't want to damage the spindle.
I have done a factory reset P0.13 =10
Is there some standard starting setting?
If I'm wasting my time with the VFD please tell me, as I'll send back but obviously want to get it going.
many thanks
Allan
-
13-12-2020 #2
The one you have will work. But I am not familiar with this it.
The one that I would use (if you could send it back) would be the tried and tested :-
https://www.ebay.co.uk/itm/Speed-Con...sAAOSw97RfAuIN
some of the important settings is the motor number of motor poles I think it is 2 if you have the Chinese 2.2kw spindle
and the input voltage & current. Also the max frequency 400Hz so the the spindle will run at 24K..Clive
The more you know, The better you know, How little you know
-
13-12-2020 #3
I've just found this sheet that is to the VFD I have, I've set as listed but not sure about the middle & low frequency & voltage settings, they don't look right to me, I'll attach a copy
thanks
Allan
-
13-12-2020 #4
Have a look here... https://en.industryarena.com/forum/h...117782-33.html, reply 655.
Don't know this VFD at all, so can't advise further other than Google is your friend.
Clive's advice above about getting motor poles/voltage is perfectly sound. You'll hate me for saying this but I wouldn't have recommended resetting any parameter without first going through the lot and recording the delivered pre-sets.
-
13-12-2020 #5
I've seen a post with these setting?
P00.00 – 50Hz
P00.04 VF highest output frequency – 400Hz
P00.05 VF maximum voltage output frequency - 400Hz
P00.06 VF highest output voltage – 100%
P00.07 VF middle frequency – 200Hz
P00.08 VF middle voltage – 50%
P00.09 VF minimum frequency - 120Hz
P00.10 VF minimum voltage – 30%
but the manual say's
P00.00 – 50Hz
P00.04 VF highest output frequency – 400Hz
P00.05 VF maximum voltage output frequency - 400Hz
P00.06 VF highest output voltage – 100%
P00.07 VF middle frequency – 40Hz
P00.08 VF middle voltage – 10%
P00.09 VF minimum frequency - 4.0Hz
P00.10 VF minimum voltage – 1%
confusing!
-
13-12-2020 #6
I wouldn't worry about the differences as none will stop it from working or damage it.
-use common sense, if you lack it, there is no software to help that.
Email: [email protected]
Web site: www.jazzcnc.co.uk
-
13-12-2020 #7
Hi JAZZCNC
do you think the top settings seem more reasonable
?
Allan
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
vfd query about the program settings for XSY-AT1 and air cooled spindle
By marbles in forum General ElectronicsReplies: 17Last Post: 11-09-2019, 11:19 PM -
Water cooled vs Air cooled spindle for wood
By Bucks in forum Machine DiscussionReplies: 5Last Post: 06-02-2017, 01:58 PM -
Water cooled / air cooled 2.2kw spindle
By suesi34e in forum Generic Chinese SpindlesReplies: 15Last Post: 25-02-2015, 04:57 PM -
Do you need to water cool erhm a water cooled spindle?!!
By HankMcSpank in forum Generic Chinese SpindlesReplies: 18Last Post: 02-10-2013, 09:59 PM -
Cooling a water cooled spindle, without pipes everywhere & huge water tanks/buckets!
By HankMcSpank in forum Generic Chinese SpindlesReplies: 17Last Post: 18-09-2013, 06:32 AM
Bookmarks