Thread: Looks impressive for the money ?
Hybrid View
-
04-01-2021 #1
So I'm looking at hooking one of these lasers onto my 1040 cnc.
Says it can cut ply single pass 8mm was skeptical but then saw someone demo it on YT
I think at that price I will take a punt , really mostly doing some etching for my daughters Etsy wooden stuff. And a few ply coasters for a friend. Anyway I'll let you know how it goes.
Specs
30W General Specification:
Model:NEJE Module 30W
Heatsink Material:Aircraft Aluminum + Brass Shell
Luminous Color:Blue
Section Size:40mm x 40mm
Cooling Mode:Temperature sensor intelligent control + 10000 rpm 40mm cooling fan
Dimension:60 * 40 * 40mm
Adapter Plug:5.5 2.1 port
Can Engrave:MDF/Balsa/Paper/Wood/Fabric/Plastic/Leather/Plywood/Foam Paper/Anodized Aluminum
Can Not Engrave:Metal/Glass/Stone/Ceramics/PCB/Stainless Steel/Reflective Material/ Transparent Material
Technical Parameters:
Module Input:20-30W
Optical power output:7.5W (7500mW)
Wavelength:445-450nm
Beam Shape:Dot (Focusable)
Working Voltage:DC 12V
TTL&PWM Modulation:YES, Compatible with Both TTL & PWM Modulation
Input Voltage:DC12V 3A
PWM/TTL Input:DC3.3V-12V
Input Interface:PH2.0-4Pin (+,-, PWM/TTL, Temperature), 3Pin (+,-, PWM/TTL) , 2Pin+2Pin (+,-) + (PWM/TTL,-)
NOTE:Temperature interface can be disconnected,NEJE provides text instructions for temperature acquisition on wiki.
Drive Mode:External ACC
Safe temperature range:<60 ℃
Module weight:202g ( The lighter the weight, the smaller the move inertia, the better the performance )
Life Time:10000-20,000 hours
Fiction is far more plausible when wrapped around a thread of truth
Nothing great was ever achieved without enthusiasm.
Ralph Waldo Emerson
-
04-01-2021 #2
Watching with interest. I'm not quite flush enough to punt £130 on a whim, but it you report good things then it's a good option.
Can I advise - get a thin sheet of ali to sit on the bed of your CNC - various materials cut tend to leach either resins or chemicals, which can mark the bed.
-
The Following User Says Thank You to Doddy For This Useful Post:
-
04-01-2021 #3
I'd personally not put a sheet of ali under an unenclosed laser. I'd put down a sheet of something sacrificial that'll absorb the laser, not reflect it around!
One thing you'll want to add is a small fan to blow fumes away. It doesn't have to be strong, just enough airflow so the smoke/fumes aren't able to rise straight back up and coat/obscure the laser lens.Avoiding the rubbish customer service from AluminiumWarehouse since July '13.
-
The Following User Says Thank You to m_c For This Useful Post:
-
04-01-2021 #4
-
The Following User Says Thank You to Doddy For This Useful Post:
-
04-01-2021 #5
I'm actually excited to have a go, the CNC has been in packing boxes for the last 18 months. But now I have my new home office big enough to get it built in, I'm going to do "stuff" lol
I'm on CAD atm working out a stand and enclosure to hand over to the smithy to make. Only problem is, hes use to making agricultural machinery so it will be made with battleship armor. I'll have to get some photos of some of the stuff he makes.. seriously over engineered lol
I have an idea for a low pressure cyclone air filtration system. I saw one at a factory I visited last year and it worked really well.
As for fire, I have a plan for that already.
Fiction is far more plausible when wrapped around a thread of truth
Nothing great was ever achieved without enthusiasm.
Ralph Waldo Emerson
-
17-07-2021 #6
So just to bring this up to date.
It looks like these lasers only work with NEJE's own controllers.
Which they don't state on the sales page on AliExpress or Amazon for that matter.
They are simply an upgrade.
Waste of $100.. be aware of this.
Fiction is far more plausible when wrapped around a thread of truth
Nothing great was ever achieved without enthusiasm.
Ralph Waldo Emerson
-
17-07-2021 #7
Deleted post - not convinced that the laser module isn't just driven by TTL-signal from the missing PWM controller. (ignore image that I can't figure out how to remove)
Last edited by Doddy; 17-07-2021 at 10:13 AM.
-
17-07-2021 #8
I understand
Last edited by Fivetide; 17-07-2021 at 05:52 PM.
Fiction is far more plausible when wrapped around a thread of truth
Nothing great was ever achieved without enthusiasm.
Ralph Waldo Emerson
-
17-07-2021 #9
Here's a question or two:-
1) Can you write software on the Arduino?, such as to test the PWM interface to the laser without the GRBL software?
2) If you have an Arduino sketch, can you Upload (compile, link and install) the software into the Arduino?
If Yes/Yes, that's your answer. If No/Yes, then I'll knock something up for you - if you're interested.
-
17-07-2021 #10
I thought (only 5 minutes casual googling) that the laser was controlled either by a TTL or PWM signal? But I'm struggling to find the spec of the PWM signal (frequency, and active level, 0%/100% reference pulse widths)
What are you driving the PWM from? (e.g. a PWM output from a BoB?) In which case there may be a general sensitivity to the PWM frequency (and you might need a mini interface to take PWM of one frequency, and re-present that at another). That's all do-able and a cheap ardi (that you already have) could be brought to bear to achieve that.
Any documentation with the laser?
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
NEW MEMBER: New member help me spend my money
By Jiroma in forum New Member IntroductionsReplies: 7Last Post: 17-08-2018, 10:40 PM -
RFQ: Can someone make this for me? For money?
By richardmayo in forum Projects, Jobs & RequestsReplies: 1Last Post: 16-11-2013, 02:00 AM -
Need some money making project ideas
By Fivetide in forum Marketplace DiscussionReplies: 10Last Post: 23-11-2012, 09:50 AM -
Which part of *your* build leaked the most money?
By CNCBlug in forum General DiscussionReplies: 3Last Post: 08-03-2010, 07:59 PM -
Easy money
By HankMcSpank in forum General DiscussionReplies: 2Last Post: 06-07-2009, 12:39 PM
Bookmarks