Threaded View
-
27-08-2021 #2
No brainer in terms of which Software is the better, UCCNC wins hands down compared to the Cslabs options. In terms of electronics and neatness then Cslabs takes some beating as its quality, that said the UC300 and UCBB are very well made also and certainly up to the task just not quite as refined or neat as Cslabs.
Careful here because you need to factor in UK VAT and postage. You will get charged VAT and a fee from the shipping agent which I believe CncDrive uses FedEx now as the shipping agent they used before no longer delivers to Uk since we left the EU.
I'm probably one of the few that can answer this with any certainty because I use both setups.!
The UB1 is the better board for a few reasons BUT not the connectors which in my opinion actually spoil the board as they are small and not very nice to use.
The UB1 wins because it's neater with no messing around with ribbon cables, etc.
Another reason is that it provides a protected 0-10V Analog Output which the UCBB doesn't have. If you need 0-10V then you have to take it directly from the UC300 pins.!!
Also, It only needs a 24Vdc PSU, not 5v and 24Vdc PSU's. The UC300 needs 5V and feeds the UCBB with 5V thru pin 26 of the IDC cable. This is a little crazy to me because the UCBB needs 24Vdc and actually generates a 5Vdc which makes it available on some of its terminals so why not feed the UC300 and do away with a 5Vdc PSU.? Which is exactly what the UB1 does.!
The UCBB is a nice well made board but it's not as clean n tidy as the UB1 and you have the other factors mentioned. That said I do use them both and keep the UCBB in stock, which I don't the UB1, but this is mostly down to cost. The UB1 features are nice but £100+ saving with no real loss of features can't be ignored.!
You won't be disappointed with either.
However, If you don't need loads of I/O then I'd give the AXBB-E a good look over because they are a fantastic neat little package, I fit these to nearly every machine I build these days except machines with ATC, etc that require lots of I/O.
In performance terms, it's exactly the same motion controller as the UC300, just with fewer ports. It also has a 0-10V analog output, unlike the UCBB.
Also, If you don't want to buy direct from Cncdrive then I have both in stock and can provide the license file for UCCNC.Last edited by JAZZCNC; 27-08-2021 at 10:44 PM.
-use common sense, if you lack it, there is no software to help that.
Email: [email protected]
Web site: www.jazzcnc.co.uk
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
New UC300ETH Breakout Board/Motherboard
By Ger21 in forum CNCdrive (UC100, UC300ETH)Replies: 10Last Post: 17-07-2019, 09:41 PM -
anyone using an e-cut 1 mhz usb breakout board
By nobby in forum Control Hardware & SystemsReplies: 10Last Post: 22-10-2018, 11:50 PM -
which breakout board?
By johngoodrich in forum General ElectronicsReplies: 4Last Post: 12-03-2017, 01:54 AM -
Breakout Board
By Tomnewry in forum General ElectronicsReplies: 2Last Post: 12-12-2013, 07:24 PM -
Breakout Board
By croy in forum Electronic Project BuildingReplies: 10Last Post: 18-08-2011, 07:50 AM
Bookmarks