3000x1500mm table drawing stage

[JAZZCNC]

If i had to attempt something this size my plan of attack would be weld the main frame, make the pads on your uprights a good thickness, after welding spot face the pads so you have a flat surface for taking shim sizes, on your top rails have some good thick pads to mate with the ones on the frame, send your two top rails away for machining of top suface and pads plus the sides for ballscrew alignment, align the top rails and measure for shims.

That's a good approach and one I mentioned before but it actually works out more for machining 2 rails than having the whole frame machined. Then you still have to deal with aligning the rail surfaces onto the same plane.!

The reason it costs more is due to setup time, the frame is just one setup, with 2 separate rails it's two setups. You do save in transport because rails will fit in a smaller vehicle.

[mekanik]

Aligning the rails should be doable what you need are two taps on each of the pads frame and rail, tabs on the frame get tapped with a fine thread so you can adjust the rail for roll & pitch/align and shim.
Was looking for a picture of Boyan's big machine yesterday but couldn't find it, also i believe Boyan has a couple of his machines in CAD if reefy86 was to get in touch, if i remember correctly Boyan stitch welded his frame to keep down distortion.
All ideas to ponder.
Regards
Mike

[JAZZCNC]

Aligning the rails should be doable what you need are two taps on each of the pads frame and rail, tabs on the frame get tapped with a fine thread so you can adjust the rail for roll & pitch/align and shim.

Yes, it's doable, I've done it many many times. I've also tried your suggestion and it doesn't work quite as well as you'd imagine on large rail surfaces. It takes an age to get right and can defeat the point of having the rails machined flat because it's so easy to introduce error if the shims are not spot on when tightened down.

The best method I've found other than sending the whole frame away for machining is a mixture of using the pads with set screws for fine adjustment like you say but also to raise the pads leaving a gap of about 3-5mm when tightened down solid. Then instead of shims use an Epoxy metal putty sandwiched between the pads with a release agent so the top rail can be removed if needed.
This method fills any voids or distortion from welding the pads and gives a very solid surface, the epoxy also acts as a vibration dampener.

Was looking for a picture of Boyan's big machine yesterday but couldn't find it, also i believe Boyan has a couple of his machines in CAD if reefy86 was to get in touch, if i remember correctly Boyan stitch welded his frame to keep down distortion.

Boyan's machine is well OTT IMO and still doesn't get away from the epoxy method which is only suitable in accuracy terms for an average machine. It also took him a few attempts and a lot of wasted money in epoxy.!

End of the day it depends on the usage of the machine and what accuracy levels your looking for or expecting. If mostly cutting woods and V carving or panel type work then usually if done correctly any of these lower expense DIY methods work great.

It's often the smaller details that show up the difference in build quality, like the example of one of my customers which I gave Reefy in an email. They produce bespoke large highly detailed doors with 2.5D scenes cut into them and for a long time struggled to produce the quality of door they wanted. They first blamed the machine because it was a merchant dice machine, then they went the DIY route and that didn't end well, so they bought a Chinese machine but still, they couldn't get the quality right.

The problem wasn't the highly detailed 2.5D scenes which were quite complex models, it was the little details like chamfers on the door edges or Grooves around the edges of panels etc, they couldn't get a consistent width along the length of doors or large panles because the rail top surface wasn't flat or on the same plane and anyone who's battled with chamfers nows, they look a mess when not right.

Now you can imagine the frustration after cutting a 12hr 2.5D scene into the door (twice) only for the last details to mess it up.

[mekanik]

It also assumes that the machine shop has a good hand that knows what he is doing, rails go face down on machine(mill/shaper/grinder) operative packs any gaps to the table making sure not to distort the rails then machines the pads, rotate the job pads down (now clamping on pads) on machine base and machine the top and at least one side.
Was thinking a decent size (thickness) shim so it could be setup in a 4Jaw chuck and machined on a lathe.
Wouldnt have thought it would be possible to get your alignment dialed in before your putty went off.
DIY Laser levelling using webcam
Regards
Mike

[JAZZCNC]

Wouldnt have thought it would be possible to get your alignment dialed in before your putty went off.

Plenty of time because you have done all the initial setup before applying the epoxy putty and then you have a good 30+mins to tweak if needed.

DIY Laser levelling using webcam

Why mess about with all that nonsense which can't be verified for accuracy when careful use of a water level will do the same job and it's guaranteed to be accurate because the law of physics doesn't lie.

But to me for between £800-£1000 for the whole frame machined complete with reference edges and tapped holes it's not worth messing about with any of this.!

[reefy86]

But to me for between £800-£1000 for the whole frame machined complete with reference edges and tapped holes it's not worth messing about with any of this.!

no brainer really, taking the costs of the epoxy with extra just in case i mess up which is highly possible along with the anxiety of not wanting to mess up and hope to god i did a good job so really its just an extra £500 to have it machined and drilled as you say. gantry and motors play a strong part but the frame is like the processor in a computer it wouldn't work without it.

ive just emailed a company called wec group to see if its something they do and how much. do you have any other recommendations?

Dean if you had that service running i would of snapped you up in a heart beat lol but jeez you must be rolling in it to get tempted to get one your self :)

[JAZZCNC]

Dean if you had that service running i would of snapped you up in a heart beat lol but jeez you must be rolling in it to get tempted to get one your self :)

"Rolling in it" I wished.. But you'd be surprised how cheap some of these large machines can be bought. The largest cost is moving them and prepping the new site.
However, my plan isn't to buy one but rather build a bespoke monster just for surfacing.!