Hybrid View
-
12-05-2022 #1
I'm not quite sure what you are asking here.? You say how they relate to the connection on the Unit.? What unit are you talking about.? Do you mean the Controller or breakout board if so then you don't say which controller or breakout board and without that, no one can help you really?
The diagram of the pinout for the drive is self-explanatory really, you decide which of the pins you are going to use and connect to the pin numbers on the 36-pin connector. Then at the other end, you have the choice to wire to the same pin numbers if it's 36pins or if the controller or bob has its own pin numbers on say a 44 pin connector then you wire to the relevant pins this requires. Often on the connector at the other end, you will pull each pin wire and send it to several places inside the control box.
We need more info on the "Unit" you talk about.-use common sense, if you lack it, there is no software to help that.
Email: [email protected]
Web site: www.jazzcnc.co.uk
-
12-05-2022 #2
Hi,
The unit in question is the Panasonic MSD043xx series servo. Not worried about the breakout board side. https://industrial.panasonic.com/con...s_manual_e.pdf
The first image in my above post shows the pin outs for the panasonic unit (from the paperwork included with the miller). But the manual does not state which pin on the physical drive connector is pin 1.
Picture 2 is what I "guess" are the pin numbers on the connection actually on the unit and the corresponding connector that connects to that.
The last picture is of the the cables that came with it, but I think they are proprietry to the Artisan boards. So of no help to me. But I can cut the serial connectors off and still use the cable.
thanksLast edited by Nemo1966; 12-05-2022 at 09:48 PM.
Every time I am wrong - the World makes a little less sense.
-
12-05-2022 #3
A bit like this one which is a db44 for a delta.
https://www.aliexpress.com/item/1005...c00PlsAmK&mp=1
The loose ends get connected to the relevant pins on your breakout/controller you want to use to control it.
Looks like a 36pin scsi on the panny to me.
Something like this and chop it to loose one end (depending on whether need male/female).
https://www.aliexpress.com/item/4001...Adapt=Pc2Msite
Or solder your own 'kit' connector together.
https://www.aliexpress.com/item/3304...Adapt=Pc2MsiteLast edited by dazp1976; 12-05-2022 at 10:03 PM.
-
12-05-2022 #4
-
12-05-2022 #5
In short... is this correct or not?????
Attachment 31027Every time I am wrong - the World makes a little less sense.
-
12-05-2022 #6
-
12-05-2022 #7
Ok, can you post the manual or a link to it.
-use common sense, if you lack it, there is no software to help that.
Email: [email protected]
Web site: www.jazzcnc.co.uk
Thread Information
Users Browsing this Thread
There are currently 8 users browsing this thread. (0 members and 8 guests)
Similar Threads
-
MSD043A1XXV Panasonic AC Servo Driver 400w - MB3 connection help
By Nemo1966 in forum Stepper & Servo MotorsReplies: 26Last Post: 22-05-2022, 05:58 PM -
MSD043A1XXV Panasonic AC Servo Driver 400w - MB3 connection help
By Nemo1966 in forum General DiscussionReplies: 2Last Post: 27-08-2020, 07:54 PM -
Dc servo driver
By Treemonkey in forum Motor Drivers & ControllersReplies: 11Last Post: 11-02-2013, 08:16 PM -
Panasonic 3 phase driver running on 1 phase?
By gavztheouch in forum Motor Drivers & ControllersReplies: 2Last Post: 10-05-2012, 11:21 PM -
FOR SALE: 400w panasonic ac brushless servo motors and drives
By gavztheouch in forum Items For SaleReplies: 3Last Post: 29-12-2011, 03:04 PM
Bookmarks