DIY Spindle - What type of bearings are best suited for a spindle.

[Ross77]

Now I can burn tools and make things way under size etc etc ... but I'm getting by

I know how you feel, I've only just started to learn how to use a lathe properly, general turning is easy, getting two parts to fit together is the hard bit

I wanted to use a keyless chuck for ease of use - I'm going to try it and move on from there...Ive just got a dremmel type mini drill with a keyless chuck

I may be wrong but I think you mean a collet chuck? keyless are like the ones on a dill with 3 jaws. A collet chuck is like on a dremmel where the bit is held by a tapered and slotted holder, compressed by the nose cone(? thing, bit:heehee:)

A collect chuck is far superior in all aspects including grip and run out, and is what most people use for cnc, Check out the ER 11 range for what you need.

Just out of interest what lathe have you inherited?

[8iggles]

I have a rotary tool with a collet type chuck, but all the bits and small end mill cutters never seem to fit !! the little mini drill thing that I'm using is a little 3 jaw chuck that will just about take a 3/16 bit at a push. its just theres a new keyless chuck in dads stuff

The collet chuck would be spot on but I can spend on essentials first like software then upgrade as I go...it says jacobs taper is that the same as the taper in the back of a bigger jacobs chuck?

The Lathe is a Faircut Junior and my Dad served his time in Sheffield and started on one of these around 1950...Then when he saw this one for sale early eighties he bought it for his retirement - I just had to make room for it and could never part with it http://www.lathes.co.uk/faircut/

[black5f]

Sounds like you're having great fun! Lovely little lathe, don't be put off if its a bit worn. as long as the headstock spindle has no lateral or longitudinal play and most older lathes can be adjusted and adjusted. I had a 55 year old tired ML7 for years. You get to know where its accurate and where not and just have fun. So the first thing to do is make yourself some bushes for the collet. I've only got about three collets because they are so expensive (they are all second hand), turned up a selection of bushes out of ali or brass. In fact, my nc mill just has one anoying metric collet and I have never got round to replacing it. Turn them to diameter and drill and ream for your cutters, then just slit them with a razor saw just over half way by hand from each end 90 degs apart, and you can use all your cutters. 2nd hand reamers are usually OK for softer metals or borrow one just for that job. Oh, if you cant already, learn to gind your own turning tools (sherline has a good pdf on that), much cheaper. Don't forget that broken files and drills are all good tool material, can be ground to the shape you want and can be mounted in mild steel bocks in the tool holder. Broken needle files make excellent small boring tools brazed into a bit of bar.

Taper drill chucks are in all sorts of sizes, popular tapers are Jacobs (JT1, JT2 etc_ and B. But they're all different. Tapers safer or just apply a little nut lock on the thread. Chucks never really run true and they wear, even if you spend a lot (drills bend anyway!). Cutters are much harder and snap, with very small cutters in a drill chuck they are really going in circles rather than rotating.

Most importantly... have fun!

[8iggles]

Yes Its great to get out in the garage - a change from the stress at work....The lathe is just right for me not too big. I will have to learn to make and sharpen tools - I found 2 boxes of new blank tools 3/8 round and square. I'm gradually mutilating my way through the ready to go ones :)
I never thought about making bushes - So If I were to buy one I could get maybe a 1/2 one and all the tools that I have are smaller
I will still use the drill chuck at first because I have got it and the accuracy is not as important as the ease of use while I'm learning, I need to get some time in using it - However I have noted what everyone is saying to me and will upgrade to a collet chuck

Thanks Shaun