Thread: Need helpwiring up from scratch
-
12-07-2010 #31
No output to the A axis either put it in slave mode over Xaxis and still no running f both axis.
Checked for continuity on tracks to IC U4 74HC541 line driver chip might be faulty?
-
12-07-2010 #32
hmmm... does Z work?
It would be very unusual for a chip to fail, these line drivers can take a lot of abuse. You could unplug the BoB from the PC and exercise each pin 2 - 9 to ground and to +5v with a bit of wire and check the voltage at pins 2 - 9 of the HC541 and the matching outputs 18 - 11 and see that they are as expected.
Its def an HC541?... you've not got the 541 and 244 swapped over (which would give exactly those symptoms i.e. 2 work, 2 dont)
Irving...
-
12-07-2010 #33
Yep Z and Y axis ae fine.
Quickets way to find out is replacing the chip,Irving as they'e only pennys to buy.
Will let you know in a dy or two how I get on with it and inform you as to whether it was the chip.
For now I've neglected other work messing around with this and I'll tackle that work till I nip down the towny for a replacement chip.
Many thanks for your help and those who chipped in,appreciated
-
12-07-2010 #34
Got another problem,since I know the Z and Y axis work I've been having a dabble to try and get to know MAch3 functions and how it works.
However in the Motor tuning setup I cannot get anything out of the motors,they jut won't turn....they work fine if I load a G-code.
Going through the PDF of how to set up Mach3 and this is the first thing it explains to do but it ain't happening for me :cry:any ideas?
Thank yer vey kindly
-
12-07-2010 #35
Dang! hold the front page chaps...I reread the PDF and must have overlooked the part where it says "Now press the up&down key on the keyboard"
-
13-07-2010 #36
-
13-07-2010 #37Ummm, think i said that in post #30...
-
13-07-2010 #38
Success,seems it wa the chip after all.
I got a couple at 30p each and also the other type as well.
Good job I put them in DIL sockets rather than directly slodered. :-)
-
13-07-2010 #39
good to know you're "on the move"... glad to help
-
13-07-2010 #40
Magic,Iving.
Is it normal for the motors to make a noise(not operating)when not in use ie no pogram running for their use?
Thanks.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
BUILD LOG: 1250 x 1250 cnc router (from scratch)
By Danielroyal25 in forum DIY Router Build LogsReplies: 56Last Post: 08-08-2014, 07:35 PM -
BUILD LOG: starting from scratch- router 1st project
By idefix in forum DIY Router Build LogsReplies: 24Last Post: 10-01-2014, 12:53 AM -
NEW MEMBER: Have Built 2 CNC machines 1 mill/drill conversion and 1 Router/plasma from scratch
By AGB in forum New Member IntroductionsReplies: 3Last Post: 06-02-2013, 03:16 AM -
Starting from scratch, what would you use as a base for a CNC metal lathe?
By m_c in forum Lathes, Lathe Rebuilding & ConversionsReplies: 4Last Post: 23-01-2011, 05:37 PM -
Building from Scratch or follow some plans?
By Monk in forum Gantry/Router Machines & BuildingReplies: 22Last Post: 12-08-2010, 10:27 PM
Bookmarks