. .
Page 1 of 2 12 LastLast
  1. Hi
    My name is keith and I fly radio controlled aircraft some of my exploits on http://www.rckeith.co.uk

    I want to build a cnc foam cutter and I've seen some good stuff on the net but most of it is USA based.
    http://www.8linx.com/

    It seems to me the biggest challenge is the motors and electronics. I earn my living from computers so that side of it is easy for me and I started as a motor mechanic many years ago so and can tackle most building projects. I've seen this board and stepper motor on ebay http://cgi.ebay.co.uk/4-Axis-TB6560-...#ht_6942wt_911 and wonder if any one has used these before and are they any good.

    Thanks for any advice

    Keith

  2. Welcome Keith

    The TB6560 boards off ebay are OK as long as you understand their limitations... dont believe the vendors specs...

    see the following threads for more info:

    http://www.mycncuk.com/forums/showth...ghlight=tb6560

    http://www.mycncuk.com/forums/showth...ghlight=tb6560

  3. The Following User Says Thank You to irving2008 For This Useful Post:


  4. #3
    I'd sooner go for 3 of these

    http://www.diycnc.co.uk/html/drv25dual.html

    one of these.

    http://www.diycnc.co.uk/html/uniport.html

    And three of these

    http://www.arceurotrade.co.uk/Catalo...Stepper-Motors

    The £25 ones.

    Total £195, all UK made or supplied and some form of guarantee.
    Slightly more and only three axis but far better gear.

    .
    John S -

  5. The Following User Says Thank You to John S For This Useful Post:


  6. #4
    John i don't Keith needs to go that far with what he wants really. I bought all the parts to build a foam cutter before starting myself. Keith as i was going to base my original build on the same machine for exactly what you are doing The cheap driver should be fine as i have two here myself and used them on a much bigger machine. You can get the draw slides as a multi pack buy from Screw Fix, i would use ACME 12 X 3 instead of the threaded rod they suggest as it will give you the higher speeds. At the end of the day you are cutting foam not a hard dense material so no need for all the extra expense. If i may even suggest you look at belts as well as you could even loose some of the motors by linking each side, use one motor for each plain. By the time you get that Obeche over you foam should look a treat.
    If the nagging gets really bad......Get a bigger shed:naughty:

  7. The Following User Says Thank You to Swarfing For This Useful Post:


  8. #5
    cutting down on the motors will only be good for straight sections not tapered..............Sorry was not thinking that one through..Doh!
    If the nagging gets really bad......Get a bigger shed:naughty:

  9. The Following User Says Thank You to Swarfing For This Useful Post:


  10. Thanks guys for all your advice.

    I will be doing tapered wings so I really need 4 -axis.

    Keith

  11. just come across this site...I have built a 4 axis machine for foam cutting using the stepper driver board you mention... it seems to work reasonably well.. I've also written some code for a hot wire controller based on Arduino 1280 mega and some simple wire heater electronics (optoisolator , power FET and some resistors on veroboard). I have versions that work with Jedicut a (and hence probably GMFC) and a different one that works with TJZOIDE. Currently looking to use profili 2 , devfus foam (from Stefano Durante) as design tools/G code creators and Mach3 as the table drive programme. Again it all seems to work quite well. Glad to share the detail and give what help I can if you're interested. I live in South Wales (just).

    regards JH

  12. Hi JH

    Thanks for you post. There's no subsitute for experience as they say. My CNC foam cutter is on hold, but I hope to get back on it in the new year. VC10 project is all consumming at the moment http://www.rckeith.co.uk/vc10 Do you have any pictures it would be nice to see some. Are you a RC flyer?

    keith

  13. well when you do get back to the CNC black magic... if you need any advice..your welcome...for what its worth I'll take some pictures tonight ..its based on stuff from EBay mainly axis-cnc ..and yes I'm an RC addict...wondered if you'd seen Dr Blacks VC10...still waiting for the Tornado from GAD myself

    regards JH

  14. Hi JH
    Yes I have seen Mike Black's VC10, he's a good friend. Paid him a visit in July while on holiday in Norfolk mainly to see his VC10. Got the inspiration after seeing Mike's CNC machines to build my own. So its Mike's fault. Look forward to your pics. My plan is build Lancaster wings and Fuselage's with the cutter using XPS foam. I have a Priory model lanc, its in bits after a speed controller failure. I have new parts from Priory models to rebuild it with brushless motors but I'd like to build my own version as well.

    Regards keith

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. laser cutter/engraver rebuild build log
    By gavztheouch in forum Laser Machines & Building
    Replies: 37
    Last Post: 10-11-2015, 05:37 PM
  2. Hot Foam cutter for RC aircraft
    By rckeith in forum Hotwire Cutting Machines
    Replies: 25
    Last Post: 10-08-2015, 08:32 AM
  3. CNC hot wire cutter
    By Nstocks in forum Machine Discussion
    Replies: 0
    Last Post: 22-05-2014, 07:54 PM
  4. CNC Hot Wire Foam Cutters
    By HotwireCutter in forum Manufacturer News
    Replies: 0
    Last Post: 02-05-2012, 09:04 PM
  5. Software for foam cutter - any recommendations
    By rckeith in forum Machine Control Software
    Replies: 2
    Last Post: 08-08-2010, 10:14 AM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •