Mill with digital scales

[irving2008]

I used the driver half of that with a 555 timer and dual comparator to chop it. Sight snag using their controller, you have to stop on the home position if you want to switch off and come back to it, you can't save the step pattern and location when you exit. It all worked okay until the mains voltage surge popped all three at once. Had to work a tad close to it's voltage limit to get any kind of speed.

I've heard glowing reports of Mach3 but I do like to be in control so I avoid commercial software as much as possible. If you write your own you can add features and fix bugs. My next software will be version 3, so I have some experience to draw on. Has to run under Windows XP and cut from an AutoCad dxf file. I want vast amounts of memory and the thought of 32 bit integers has become almost irresistable. The GUI is good to :D

Love to see it Robin. Was thinking of writing my own DXF->GCode as haven't found one I truely like and what I want is seamless CAD -> mill (or PCB layout -> mill). Although I have lots of free software that does the job its all a bit of a faff and kludge.

Going to stick with L297/L298 at 40v/2A for now as my steppers and 2mm ACME screws don't need any more, but have a 4-axis design on the drawing board using a PIC processor, 2109 hi/lo drivers and discrete MOSFETs for 80v, 5A/coil, 1/8 microstepping capability for the future.

Where do you source your electronic parts from? I use Radiospares, Farnell (rarely, since mostly seems to be US-stock now), Maplins (even less so), and Cricklewood Electronics all online - the days of the great electronics shops have long gone :(

[Robin Hewitt]

I've done the read a dxf, pick out lines arcs and circles then stitch lines and arcs together into shapes (fudging the ends slightly so they meet up properly). Also the expand/contract it bit to get the tool path.

No G-Code planned, it goes straight to my box of tricks and turns the handles. I have a wicked arc drawing algorythm my brother wrote, any start point, any end point, either direction. I just call it and it gives the next pixcel on the arc. I tried it drawing circles on screen, then had to add a delay between pixcels so you could actually see where it started and which way it was going :D

My preferred small quantity supplier has to be Rapid Electronics.

40 volts is very close to smoke if you're using a transformer, suggest you do something clever in the PSU to protect it.

[irving2008]

I've done the read a dxf, pick out lines arcs and circles then stitch lines and arcs together into shapes (fudging the ends slightly so they meet up properly). Also the expand/contract it bit to get the tool path.

No G-Code planned, it goes straight to my box of tricks and turns the handles. I have a wicked arc drawing algorythm my brother wrote, any start point, any end point, either direction. I just call it and it gives the next pixcel on the arc. I tried it drawing circles on screen, then had to add a delay between pixcels so you could actually see where it started and which way it was going :D

Sounds interesting... so lets see some pics :)

My preferred small quantity supplier has to be Rapid Electronics.

Thanks, I'll go investigate

40 volts is very close to smoke if you're using a transformer, suggest you do something clever in the PSU to protect it.

Yes I know. Go to do a back-emf dumper and some sort of voltage limiter (not a regulator as such) - looking at some ideas that combine the two. Don't want to use a series regulator cos of the losses involved at 6A+ (if all 3 axis active) but thinking along lines of series/shunt MOSFETS (got a couple of samples rated at 120A, 200V and 0.003ohm Rds, so even at 10A its not going to get warm if turned fully on!)

[Robin Hewitt]

Sounds interesting... so lets see some pics :)

I could do a movie of me slaving over a hot PC but apart from that there is little to see yet.

Now working on the command protocol, having a slight snag with a worst case fast traverse doing 2 steps in one axis and 1 step in the other. It's a baud rate thing :D

[irving2008]

My preferred small quantity supplier has to be Rapid Electronics.

Thanks, I'll go investigate

Well I priced the parts for my controller from Rapid - they came out about 3% more expensive than Cricklewood and didn't have a couple of parts but had some better options on others... Only sell resistors in packs of 100 though.

[Robin Hewitt]

Well I priced the parts for my controller from Rapid - they came out about 3% more expensive than Cricklewood and didn't have a couple of parts but had some better options on others... Only sell resistors in packs of 100 though.

That's a surprise because they are having a sale at the mo'. I ordered a hundred quids worth yesterday and it was on my desk by 10:30 this morning :D

[irving2008]

Robin,

Have you seen this thread on CNCZone discussing PIC-based DRO capbility using cheap chinese scales?

regards,
Irving...

[irving2008]

I guess, seeing as you posted there tonight, the answer is now yes :)