Motion Control drivers and motors

[bruce_miranda]

Aiming for Parallel and don't know what the wiring should be. So any help with be nice here.

Gary from Motion told me that the SW4 was meant only for dropping current down to half after a phase but I'm so lost now I'll try anything.

[Gary]

Wiring looks fine, and the current is set to 4.2 A so that should be ok also.
The problem that you are seeing is a typical noise or low signal problem, or possibly both.
These are the points you need to address:

1) Use Shielded cable for all signal cables
2) Shield the motor phase cables.
3) keep signal and power / phase cables apart, and if they need to cross, they should cross perpendicular.


Also check the signals from the pc, the voltage should be about 5V, it it is low the driver can miss pulses and you can get the stuttering you are seeing.

[Gary]

I just had an email from Bruce, and it apears that his clock pulse is about 3.3V, and he is using a laptop.
This is most definately the problems, and is actually quite common when a laptop is used.
The solution would be to use either another laptop with higher voltage outputs, or a desktop PC with a parallel port.

Bruce,
Try this and give us your results.

Thanks

Gary

Aiming for Parallel and don't know what the wiring should be. So any help with be nice here.

Gary from Motion told me that the SW4 was meant only for dropping current down to half after a phase but I'm so lost now I'll try anything.

[irving2008]

I just had an email from Bruce, and it apears that his clock pulse is about 3.3V, and he is using a laptop.
This is most definately the problems, and is actually quite common when a laptop is used.
The solution would be to use either another laptop with higher voltage outputs, or a desktop PC with a parallel port.

Bruce,
Try this and give us your results.

Thanks

Gary

What breakout board is he using? The MDS drivers are optisolated so dont really need a sophisticated BOB and are pretty immune to cross-over noise on the signal lines due to the low impedance 'on' drive. Unless he has a very long cable from PC to BOB or the BOB is a old design with TTL rather than CMOS logic I'd be suprised that the use of a laptop was an issue.

[Gary]

Mot sure about the Bob, but The measured voltage was 3.3V, which is on the border line of working for the optos.
I have found that most support calls that end with the signal voltages being too low were on laptops.

What breakout board is he using? The MDS drivers are optisolated so dont really need a sophisticated BOB and are pretty immune to cross-over noise on the signal lines due to the low impedance 'on' drive. Unless he has a very long cable from PC to BOB or the BOB is a old design with TTL rather than CMOS logic I'd be suprised that the use of a laptop was an issue.

[bruce_miranda]

Mot sure about the Bob, but The measured voltage was 3.3V, which is on the border line of working for the optos.
I have found that most support calls that end with the signal voltages being too low were on laptops.

Don't say that after I've just spent £33 on a BOB! Not to mention having already spent £10 for the previous BOB which won't be used.

I'll update this thread the moment I find something else worth reporting.

Anyone else here using a CNC Fusion kit? I've had alignment issues with the Z axis in particular. Is it right that the entire weight of the Z axis is taken by the collar supplied in your kit? Also why is there so little space made around the LoveJoys? The Orange sticker peeled out on a couple - just shows how close they are to the walls.

[Gary]

When we initially talked i presumed you were using our Bob, and this is a straight through bob with no components but two connectors.
What bob are you using?

Don't say that after I've just spent £33 on a BOB! Not to mention having already spent £10 for the previous BOB which won't be used.

I'll update this thread the moment I find something else worth reporting.

Anyone else here using a CNC Fusion kit? I've had alignment issues with the Z axis in particular. Is it right that the entire weight of the Z axis is taken by the collar supplied in your kit? Also why is there so little space made around the LoveJoys? The Orange sticker peeled out on a couple - just shows how close they are to the walls.

[bruce_miranda]

I am using a similar BOB but was half the price and made by a CNC user, the board is milled on a CNC machine itself and comes with 4 PCB stand-offs.

http://www.cncdoctor.co.uk/ParallelP...ard(P.004).pdf