Thread: pulley ratios on 3 pulley axis
-
21-07-2011 #31
Velocity is et to 30 as well, full speed in less that a second sounds ok to me? i will be putting it higher but remember i only have a single motor on that axis (double stack neme34) around about 1000oz of torque
If the nagging gets really bad......Get a bigger shed:naughty:
-
21-07-2011 #32
Note to myself - buy a laptop with a better keyboard, i type faster than it responds
If the nagging gets really bad......Get a bigger shed:naughty:
-
21-07-2011 #33
It depends what you're doing. For engraving where the machine has to change direction rapidly and regularly you will certainly want more.
Increase the velocity until it just stalls (30*60=1800mm/min seems a bit slow but maybe not as I don't know the mass of your gantry) then back it off by about 10-20% just to be safe. Then increase the acceleration untill it stalls whilst accelerating, and do the same.
Then change the keyboard layout to Dvorak like I have then you'll be touch-typing faster than it responds...
-
21-07-2011 #34
Gantry must be somewhere near about 20kg and thats without the dc spindle motor i will need to mount later when I've finished modding the ER16 end. A soon as can i will post some pics up on my log which i have neglected for a very long time (family stuff takes over). I have a list of changes for it already but need the machine to make the changes. i am glad to see that you have come a long way since you started Jonathan and thanks for the help, you too John
If the nagging gets really bad......Get a bigger shed:naughty:
-
21-07-2011 #35
PS
Give EMC2 a try, you WILL (look into my eyes not around my eyes) like it better that Mach3 me thinksIf the nagging gets really bad......Get a bigger shed:naughty:
-
21-07-2011 #36
I will ... I remember reading JohnS saying that you can't jog the machine whilst in feed hold with EMC? If that's still the case then that alone is probably enough to stop me using it again as it will make tool changes more difficult. That's the only reason really I haven't already used it extensively. I'm not put off with it using Linux as I do use Ubuntu for occasionally. The GUI is much nicer in EMC, in my opinion there's too much eye-candy in mach3.
Forgot to say in last post ... don't just test the feedrate by jogging. The worst case is probably when the X-axis changes direction rapidly. So for instance try something like this:
G0 X100
G0 X0
G0 X100
G0 X0
etc
(and since EMC does support loops in Gcode you can do that much more efficiently than in mach3! I remember once spending a while writing the Gcode to do pulleys using loops and stuff only to realise mach3 does not easily support conditional Gcode). Also make it move the Y and Z at the same time as you're testing X as the extra load on the power supply will make a difference. It has on my machine ... I connected oscilloscope to the power supply recently and that showed the ripple increase markedly when all the steppers were running.
No worries...yes I have learnt a fair bit since starting my router. If you compare what it looked like in the first post of my build log to now there's quite a difference! A lot of that was down to trying to cut costs though.Last edited by Jonathan; 21-07-2011 at 12:49 AM.
Thread Information
Users Browsing this Thread
There are currently 2 users browsing this thread. (0 members and 2 guests)
Similar Threads
-
1:1 ratio - pulley sizes
By dsc in forum Belt Drive, Pulleys & TimingReplies: 3Last Post: 12-04-2014, 01:30 PM -
Cutting HTD pulley(s)
By Jonathan in forum Metalwork Project ShowcaseReplies: 2Last Post: 11-12-2012, 07:19 PM -
pulley dims for boxford csb
By onecut in forum Boxford LathesReplies: 5Last Post: 23-09-2012, 04:58 PM -
4th Axis timing pulley + Axminster bandsaw review
By Jonathan in forum Metalwork Project ShowcaseReplies: 4Last Post: 09-04-2011, 07:31 PM -
WANTED: Timing Pulley Suppliers?
By m_c in forum Items WantedReplies: 4Last Post: 02-11-2008, 01:02 AM
Bookmarks